Axis VT Verso Operating Instructions Manual - Page 7

Browse online or download pdf Operating Instructions Manual for Camera Accessories Axis VT Verso. Axis VT Verso 14 pages. Camera housing and accessories
Also for Axis VT Verso: Datasheet (2 pages)

Print Page

Custodia per telecamera ed accessori

Ventilatore

Ingombro :

40 x 40 x 20 mm

1.6 x 1.6 x 0.8 in

Alimentazione :

12 VDC, 1W

24 VDC, 1.2W

Switch antiapertura (solo versione 420mm)

Max. 24VAC/VDC 0.5 A

(Figura 10)

Alimentatore per telecamera

Ingombro:

75,5 x 50 x 32,3 mm

3 x 2 x 1.3 in

Tensione di ingresso: 100-240 VAC

Tensione di uscita: 12 VDC

Corrente fornita: 1A

Peso: 123 g

(Figura 5)

Ingombro:

67,2 x 52,2 x 40 mm

2.6 x 2 x 1.6 in

Tensione di ingresso: 230 VAC

Tensione di uscita: 24 VAC

Corrente fornita : 400 mA

Peso: 380 g

(Figura 6)

Pressacavi:

(valore della coppia di serraggio)

PG9= 3,75 Nm

PG11= 3,75 Nm

ITALIANO

Supporti

Staffa a parete

Dimensioni:

80x122x205 mm

3.1x4.8x8.1 in

Peso: 0,55 kg

Fissaggio a parete, lo snodo consente la

regolazione su due assi, portata 25 kg, pas-

saggio interno dei cavi. Vedi figura 13.

Staffa a parete

Dimensioni:

70x115x285 mm

2.8x4.5x11.2 in

Peso: 0,6 kg

Fissaggio a parete, lo snodo consente la

regolazione su due assi, portata 25 kg.

Vedi figura 14.

Staffa a soffitto

Dimensioni:

ø170x270x390 mm

ø6.7x10.6x15.4 in

Peso: 1,3 kg

Fissaggio a soffitto, lo snodo consente la

regolazione su due assi, portata 25 kg.

Passaggio dei cavi interno al supporto ed

allo snodo. Vedi figura 15.

Staffa a soffitto

Dimensioni:

ø170x255x390 mm

ø6.7x10x15.4 in

Peso: 1,4 kg

Fissaggio a soffitto, lo snodo consente la

regolazione su due assi, portata 25 kg.

Passaggio dei cavi interno al supporto.

Vedi figura 16.

Staffa a colonna

Dimensioni:

ø 110x235 mm

ø 4.3x9.3 in

Peso: 0,45 kg

Fissaggio a colonna, lo snodo consente la

regolazione su due assi, portata 25 kg.

Vedi figura 17.

ENGLISH

DESCRIPTION

Modern, innovative, waterproof housing,

completely made of the latest, strongest tech-

nopolymer. The side opening greatly simpli-

fies the access to the camera, to the optics

and to all connections.

This housing is compatible with 1/2", 1/3"

and 1/4" cameras fitted with fixed focus or

small zoom lenses available on the market.

It is designed to be assembled with the

cables passing inside the bracket or with

external wiring using two PG9 and one

PG11 for 420mm version, 1 PG9 and 1

PG11 for 360mm version.

It guarantees a weatherproof standard IP66

when the cable glands are present and there

is the possibility of using a wide range of

accessories allowing indoors or outdoors

installation.

It is available in the versions with an internal

useful area of 70x70x270mm (420mm) and

63x63x210mm (360mm).

Turn off the power before performing

any operations.

Products and accessories

Depending on the configuration provided,

the housing can be used with:

Sunshield

Heater kit

Blower kit

Power supply kit

Support circuit with tamper switch (only

420mm version) (Fig. 8)

INSTALLATION

How to open the housing

To open the housing, loosen the two screws

on the side (Figure 1), turn the cover and the

upper half of the body about the opening

hinge axis. In this way there will be easy

access to the inside of the housing.

Camera housing and accessories

How to install the camera

This section describes how to install the

camera inside the housing. It should be

remembered that the power supply can be

taken from the circuit supplied after making

sure it is correct one.

1. Open the housing as described

before.

2. Extract the internal support slide by

partially loosening the fastening

screws (Fig. 2, point 1).

3. Move the slide, by sliding it until the

holes coincide with the slide locking

screws (Point 2).

4. Fasten the camera with the 1/4"

screw; if necessary place the insula-

ting spacer between the camera and

the upper half of the slide (Point 3).

If necessary, use the supplied spacers

to correctly position the camera and

optics .

5. Reposition the internal slide by tighte-

ning the previously loosened screws.

6. Close the housing after making the

necessary electrical connections.

How to install the heater kit

This section describes how to install the hea-

ter option in the dust-proof housings not pro-

vided with. Heaters can be supplied with

working voltages of 12-24 VDC/VAC or

115-230 VAC and include the pre-wired

heating element suitable for the working vol-

tage, metal dissipators and kit fastening

screws.

1. Open the housing as described before.

2. Fix the heater kit to the prearranged

points on the body of the housing

(Figure 3, point 1).

3. The pre-wired heating element should

be positioned between the two dissi-

pators (Figure 3A) before attachment

to ensure contact and hence guaran-

tee correct heat diffusion.

4. Pass the heating wire into the provi-

ded seatings .

5. Insert the two-pin connector at the end