Digicom PCI WAVE 54 Quick Manual - Page 2

Browse online or download pdf Quick Manual for PCI Card Digicom PCI WAVE 54. Digicom PCI WAVE 54 2 pages.

Print Page
PCI WAVE 54
Quick Guide
rev. 1.1 10/2005
Dear Customer,
thank you for purchasing a Digicom product.
DESCRIPTION
PCI Wave 54 supports the new IEEE 802.11g
standard, with speed up to 54Mbps, for the best
performances in a Wireless connection. PCI
Wave 54 also complies with the IEEE 802.11b
standard to guarantee the compatibility with the
old 11Mbps networks.
PCI Wave 54 supports "Ad-Hoc" applications (Peer-to-Peer Networking without Access
Point), and "Infrastructure" applications (Networking with Access Point).
PCI Wave 54 operates with Windows XP, 2000, Me, 98SE.
SOFTWARE INSTALLATION
In order to use the card correctly it is necessary to install the driver of the device and an
utility for the configuration.
Attention: Do not insert the card in the PC before you run the Software installation.
1. Before connecting your PCI Wave 54, run the utility installation. Insert the Cd-Rom
you found in the package, then go throught the following steps: Start > Run > Browse...
search for the Setup.exe file in the card folder, select it and click OK.
2. During the installation follow the on-screen instructions.
3. At the end click Finish.
4. Shut down your computer and go on with HARDWARE INSTALLATION.
HARDWARE INSTALLATION
1. Turn off the computer and unplug the power cord, remove the computer's cover.
Select an available PCI slot and push firmly, but gently, until PCI Wave 54 is well
seated. Put back the computer's cover, connect the power cord and turn it on.
2. Windows will detect the new hardware. Select Install the software automatically
and click Next.
3. Windows will automatically install the device using the driver previously copied in the
utility installation.
4. Click Continue Anyway in the Hardware Installation window.
5. Select the right Country.
6. At the end click Finish.
7. The installation is over and PCI Wave 54 will search for the Wireless devices.
CONNECT TO A WIRELESS NETWORK THROUGH AN ACCESS POINT
Select Start > Control Panel > Network connections.
Right click on the Wireless network connection, icon and select Properties. Disable
the Use Windows to configure... checkbox in order to use the provided utility for the
card set up.
From Start > Programs > 802.11 Wireless LAN run utility configuration.
Select the Network folder and check the detected Wireless devices. Select the Access
Point you wish to connect and click Connect.
To increase the security, enable the Encryption in Configuration folder.
In the Network card Properties set the right IP address for your wireless network
connection.
CONNECT TO A WIRELESS NETWORK WITHOUT AN ACCESS POINT
In order to set up a Wireless Peer-to-Peer network (Ad-Hoc mode), use the above
described configuration utility, setting the same SSID, Channel and Security parameters
in each client configuration.
For further information, read the User's Guide in the Cd-Rom, connect to the
Support area on our website www.digicom.it, or write an e-mail to
ENVIRONMENTAL CONDITIONS
Enviromental temperaturefrom 0 to +50°C
Rapid changes of temperature or humidity should be avoided.
This equipment, including cables, should be installed in an area free from:
Dust, humidity, heat from direct sun light.
Objects which irradiate heat. These could cause damage to the container or other
problems.
Objects which produce a strong electtromagnetic field (loudspeakers, etc.)
Liquids or chemical corrosive substances.
CLEANING THE TERMINAL
Use a clean and soft cloth. Wet the cloth with water or natural detergent if it is necessary
to remove any stains. Never use chemical products such as petrol or solvents.
VIBRATIONS OR DROPPING
Caution against vibrations and dropping.
DECLARATION
OF CONFORMITY
We, Digicom S.p.A. with registered office at: via Volta 39 - 21010 Cardano al Campo
(Varese - Italy) declare under our sole responsability that the product:
Name: PCI WAVE 54 satisfies the basic requirements of the below indicated Directive:
1999/5/CE of March 9 1999, R&TTE as having been designed in conformity with
the requirements of following Reference Standards:
- EN 300 328-2
- EN 301 489-1
- EN 301 489-17
- EN 60950
Relative humidity from 5 to 90% n.c.