Epson 2180 - LQ B/W Dot-matrix Printer Manual - Page 26
Browse online or download pdf Manual for Printer Epson 2180 - LQ B/W Dot-matrix Printer. Epson 2180 - LQ B/W Dot-matrix Printer 30 pages. Impact printer
Also for Epson 2180 - LQ B/W Dot-matrix Printer: Specifications (2 pages)
Print Page
EPSON LQ-2180
Clearing Paper Jams
To clear a paper jam, follow these steps:
1. Press the
button to turn off the printer.
Operate
2. If a single-sheet of paper is stuck on the paper guide, gently
remove it.
3. Remove the printer cover. If you are loading continuous
paper from the rear slot, remove the paper guide.
4. If continuous paper is jammed in the printer, tear off the
fresh supply at the perforation nearest the paper entry slot.
5. Turn the knob on the right side of the printer away from
you to eject the paper in the printer. Remove any remaining
pieces of paper.
Caution:
Use the knob on the right side of the printer only to clear
paper jams when the printer is off. Otherwise, you may
damage the printer or lose the top-of-form or tear-off
position.
6. Replace the printer cover, and the paper guide if necessary.
Then close the paper guide cover.
7. Press the
button to turn on the printer. Make sure
Operate
the
and
Paper Out
Pause
About Your Printer's Default Settings
The printer's default settings control many printer functions.
While you can often set these functions through your software
or printer driver, you may sometimes need to change a default
setting from the printer's control panel using the default-
setting mode.
The following table lists the default settings and the options
you can select in the default-setting mode. To change the
default settings, see "Changing Default Settings" on this page.
Settings
Options
Page length for front
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5,
tractor*
11, 70/6, 12, 14, 17
Page length for rear
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5,
tractor*
11, 70/6, 12, 14, 17
Skip over perforation
On, Off
Auto tear off
On, Off
Auto line feed
On, Off
Print direction
Auto, Bi-D, Uni-D
I/F mode
Auto, Parallel, Optional
Auto I/F wait time
10 seconds, 30 seconds
Software
ESC/P2, IBM 2391 Plus
26 - EPSON LQ-2180
lights are off.
Settings
Character table
International character set
for Italic table
0 slash
High-speed draft
Input buffer
Buzzer
Auto CR (IBM 2391Plus)**
A.G.M. (IBM 2391Plus) **
Font
Roll paper
*
The options available vary depending on the country.
**
These settings take effect only when IBM 2391 Plus
emulation is selected.
Changing Default Settings
Follow the steps below to enter the default-setting mode and
change the printer's default settings.
Note:
To print the language selection and default-setting mode instructions,
you need three sheets of letter- or A4-size single-sheet paper or three
pages of continuous paper that is at least 11 inches (279 mm) long
and 8.27 inches (210 mm) wide.
If you use single sheets, you need to load a new sheet of paper each
time the printer ejects a printed sheet.
1. Make sure paper is loaded and the printer is turned off.
Caution:
Whenever you turn off the printer, wait at least five
seconds before turning it back on; otherwise you may
damage the printer.
2. Hold down the
Pitch
button to turn on the printer. The printer enters the
default-setting mode and prints the language selection
instructions (one page).
3. Press the
button until the Pitch lights indicate the
Pitch
language you want, as described in the language selection
instructions.
2/99
Options
Standard model:
Italic, PC 437, PC 850, PC 860, PC 863,
PC 865, PC 861, BRASCII, Abicomp,
Roman 8, ISO Latin 1, PC 858,
ISO 8859-15
All other models:
Italic, PC 437, PC 850, PC 437 Greek,
PC 853, PC 855, PC 852, PC 857, PC 864,
PC 866, PC 869, MAZOWIA, Code MJK,
ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774,
Estonia, ISO 8859-2, PC 866 LAT,
PC 866 UKR, PC APTEC, PC 708, PC 720,
PC AR864, PC 860, PC 865, PC 861, PC
863, BRASCII, Abicomp, Roman 8, ISO
Latin 1, PC 858, ISO 8859-15
Italic U.S.A, Italic France, Italic Germany,
Italic U.K., Italic Denmark1, Italic Sweden,
Italic Italy, Italic Spain1
On, Off
On, Off
On, Off
On, Off
On, Off
On, Off
OCR-B, Orator, Orator-S, Script C,
Roman T, Sans Serif H
On, Off
button while you press the
Operate