Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Manual - Page 11
Browse online or download pdf Manual for Printer Epson C11C640001 - LX 300+II B/W Dot-matrix Printer. Epson C11C640001 - LX 300+II B/W Dot-matrix Printer 17 pages. Epson lx-300: user guide
Also for Epson C11C640001 - LX 300+II B/W Dot-matrix Printer: User Manual (50 pages)
Print Page
Your top-of-form position setting remains in effect until you
change it, even if you turn off the printer.
The top margin setting made in some software
applications overrides the top-of-form position setting
you make with the Micro Adjust feature. If necessary,
adjust the top-of-form position in your software.
If you want to restore the printer's default top-of-form position,
you can reset the printer. See "Restoring the printer's default
settings" on page 14 for instructions.
Advancing paper to the tear-off edge
When the push tractor is installed, you can use the tear-off
feature to advance your continuous paper to the printer's tear-
off edge when you finish printing. You can then easily tear off
the printed document. When you resume printing, the printer
automatically feeds the paper back to the top-of-form position;
so you can save the paper normally lost between documents.
You can use the tear-off feature in two ways:
❏
Manually, by pressing the printer's
❏
Automatically, by turning on the Auto tear off function in
Default Setting mode.
Using the Tear Off button
After the printer finishes printing your document, check that
the Tear Off (Font) lights are not flashing. Then press the
(
) button. The printer advances the paper to the
Tear Off
Font
tear-off edge.
If the Tear Off (Font) lights are flashing, the paper is in
the tear-off position. If you press the Tear Off (Font)
button again, the printer feeds your paper to the next
top-of-form position.
Advancing paper to the tear-off position
automatically
To automatically advance your printed documents to the tear-
off position, you need to turn on the Auto tear off mode and
select the appropriate page length for continuous paper in
Default Setting mode. For instructions, see "Default Settings"
on page 14.
When Auto tear off is on, the printer automatically advances the
paper to the tear-off position whenever it receives a full page of
data or a form feed command followed by no more data.
(
) button
Tear Off
Font
7/06
Adjusting the tear-off position
If your paper's perforation is not aligned with the tear-off edge,
you can use the Micro Adjust feature to move the perforation to
the tear-off position.
Follow these steps to adjust the tear-off position:
1. Make sure the Tear Off (Font) lights are flashing (the paper
is at the current tear-off position). You may need to press
the
(
) button to advance the paper to the
Tear Off
Font
tear-off position.
2. Open the printer cover.
3. Hold down the
Pause
printer beeps and the Pause light begins to flash as the
printer enters Micro Adjust mode.
4. Press the
D button to feed the paper backward, or
LF/FF
press the
U button to feed the paper forward,
Load/Eject
until the paper perforation is aligned with the tear-off edge
on the paper tension unit.
The printer has a minimum and a maximum tear-
off position. If you try to adjust the tear-off
position beyond these limits, the printer beeps
and stops moving the paper.
5. After you set the tear-off position, press the
to exit Micro Adjust mode.
6. Tear off the printed pages.
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and begins printing.
Your tear-off position setting remains in effect until you
change it, even if you turn off the printer. (If you want
to restore the printer's default tear-off position, you can
reset the printer. See page 14 for instructions.)
Epson LX-300+II
button for about three seconds. The
Tear-off edge
Pause
Epson LX-300+II
button
11
-