FIBARO FGMS-001 Operating Manual

Browse online or download pdf Operating Manual for Accessories FIBARO FGMS-001. FIBARO FGMS-001 2 pages. Motion sensor
Also for FIBARO FGMS-001: Operating Manual (20 pages), Operating Manual (11 pages)

Print Page

ENG

I. GLOSSARY OF TERMS

• INCLUSION (adding a device, learning mode) - a device sends the

Z-Wave Node Info command frame allowing to add the device to the

Fibaro System (Home Center)

• EXCLUSION (removing / deleting a device) - removing a device

from the Fibaro System.

• ASSOCIATION - controling other devices within the Fibaro System

• MultiChannelAssociation - controling other multi-channel devices

within the Fibaro System.

II. Z-WAVE NETWORK INCLUSION

The Fibaro Motion Sensor can be included into the Z-Wave network

by using the B-button.

1) Insert the battery into the Fibaro Motion Sensor. Enclosure lock is

OPERATING MANUAL

marked with a dot. Make sure the device is located within the direct

range of the main controller.

FIBARO MOTION SENSOR

2) Set the main controller into the learning mode (see main

controller's operating manual).

FGMS-001-EN-A-V1.00

3) Quickly, triple click the B-button - LED diode will glow blue.

4) Fibaro Motion Sensor will be detected and included in the Z-Wave

network.

5) Wait for the main controller to configure the sensor.

The Fibaro Motion Sensor is a universal Z-Wave multi-sensor. Along

6) If necessary, wake up the Motion Sensor by triple clicking the

with detecting motion the device measures the temperature and light

B-button.

intensity. The sensor has a built-in accelerometer to detect any

7) LED diode will glow blue to confirm the sensor woke up, and then

tampering of the device. The Fibaro Motion Sensor is battery powe-

wait for the main controller to configure the sensor.

red device and designed to be installed quckly and easily on any

surface. The LED indicator signals motion, temperature level, opera-

ting mode and can be used to see if device is within the Z-Wave

network. The motion sensor can be used for lighting scenes and

security monitoring systems.

SPECIFICATIONS

Power Supply:

CR123A battery, 3.6 VDC

EU directive compliance:

LVD 2006/95/WE

EMC 2004/108/WE

R&TTE 1999/5/WE

RoHS II

Recommended installation height:

2,4m

Operational Temperature:

0-40

Measured Temperature Range:

-20 to 100

Diagram 1 - B-button.

Temperature Measuring

Accuracy:

0,5

C (within 0

C-40

C range)

III. EXCLUDING SENSOR FROM THE Z-WAVE NETWORK

Light Intensity Measuring Range:

0-32000 LUX

1) Make sure the sensor is connected to power source.

Radio Protocol:

Z-Wave

2) Set the main controller into the learn mode (see main controller's

operating manual)

Radio Frequency:

869 MHz EU;

3) Quickly, triple click the B-button, located on Fibaro Motion

908 MHz US;

Sensor's enclosure.

921 MHz ANZ;

4) LED diode will glow blue confirming the device has been excluded

869 MHz RU;

from the network.

Range:

up to 50 m outdoors

up to 30 m indoors

IV. SENSOR INSTALLATION

(depending on terrain and

building structure)

1) Include the device into the Z-Wave network (see p.II). Note that

the inclusion process may be performed ONLY in direct range of the

TECHNICAL INFORMATION

main controller.

2) Install the sensor's holder in desired location.

3) If the sensor is already included in the Z-Wave network, wake it up

- Compatible with any Z-Wave controller.

by triple clicking the B-button.

- Detects motion using a passive IR sensor.

4) Insert the Motion Sensor in its holder.

- Measures the temperature.

5) Test the sensor's operation - check whether the LED diode

- Measures the light intensity.

indicates motion detection.

- Easy installation on a wall or any surface.

6) Test the Z-Wave network assuring the device is within range.

- Protected against tampering and theft - once vibrations are

detected, the notification is sent to the main controller.

- Alarms of movement and temperature are signaled by LED diode

blinking.

- Simple earthquake detector mode.

NOTE

Read this manual before attempting to install the

device.

Failure

observe

recommendations

included in this manual may be dangerous or cause

a violation of the law. The manufacturer, Fibar Group

Sp. z o.o., will not be held responsible for any loss or

damage resulting from not following the instructions

of operating manual.

NOTE

Work within local code height requirements for

installation of the Fibaro Smoke Sensor. Take

special precautions during installation and use tools

and equipment in perfect working order. It's

recommended to observe ladders, lifts and other

obstacles.

Diagram 2 - Motion detector, light sensor, LED diode.

NOTE

When handled carelessly or used in non-specified

environment conditions, the device may not function

properly. It's highly recommended to take all safety

precautions

ensure

safety

and

property

protection.

B-BUTTON

Diagram 3 - preparing Fibaro Motion Sensor for operation.

SENSOR

Diagram 4 - Fibaro Motion Sensor installation.

Diagram 5 - Fibaro Motion Sensor's proximity area.

V. DETECTION AREA AND WORKING CONDITIONS

Fibaro Motion Sensor's detection area is shown in diagram #6.

Fibaro Motion Sensor has to be installed in a corner of the room or

perpendicularly to the doors.

Actual range of the sensor can be influenced by environment

conditions. Should false motion alarms be reported, check for any

moving objects within the sensor's detection area, such as trees

blowing in the wind, cars passing by, windmills. False motion alarms

may be caused by moving masses of air and heat as well. If the

device keeps on reporting false alarms, despite eliminating all of the

above-mentioned factors, install the device in another place.

3 m

0 m

7 m

5 m

0 m

5 m

STICKER

7 m

Diagram 6 - Fibaro Motion Sensor's motion detection area.

VI. INSTALLATION NOTES

Fibaro Motion Sensor cannot be pointed at any source of heat (e.g.

radiators, fireplaces, cookers, etc.) or at any source of light (direct

sunlight, lamps).

It's not recommended to install the motion sensor in places prone to

drafts. Sensor can be mounted using screw or the sticker.

VII. RESETTING THE FIBARO MOTION SENSOR

The Fibaro Motion Sensor reset erases the EPROM memory,

including all information on the Z-Wave network and the main

controller.

Fibaro Motion Sensor reset procedure:

1) Make sure the battery works and is in place.

2) Press and hold the B-button for 4-6 seconds until the LED glows

signaling the 2nd menu level.

3) Release the B-button.

4) Again, press the B-button briefly.

XI. SENSOR'S ORIENTATION IN SPACE

Successful reset will be confirmed with the LED changing colour to

red and fading.

The Fibaro Motion Sensor has a built-in accelerometer. When the

value of parameter 24 is set to 2 or 3, Z-Wave networ controller will

be informed on the Sensor's orientation in space.

NOTE

Device reset will not remove it from the Z-Wave

network main controller's memory. Before resetting

XII. LED VISUAL INDICATORS AND SETTINGS

the device, it must be excluded from the Z-Wave

network.

The Fibaro Motion Sensor is equipped with a LED diode for

indicating sensor's operating modes and alarms. In addition the LED

indicator may inform of the Z-Wave network range and the current

VIII. OPERATING WITHIN THE Z-WAVE NETWORK

temperature.

LED indicator modes:

Fibaro Motion Sensor has a bulit in motion detector, temperature

1) Motion Alarm's colour will vary depending on the temperature. The

sensor and light intensity sensor, which make it a multi-channel

colour and the signaling mode can be set in parameter 80.

device. In the Home Center 2 menu it will be presented as three

2) Tamper alarm is signaled with an alternating blinking in red - blue

devices, depending on the main controller software version.

- white.

3) The Z-Wave Node Info command frame is signaled with glowing

in blue. Node Info command frame is sent each time the device

NOTE

wakes up.

Fibaro

Motion

Sensor

capabilities

will

vary

depending on the Z-Wave network controller. Certain

To enter MENU press and hold the B-button for 3 seconds. MENU

functionalities of the Fibaro Motion Sensor may not

levels will be signaled with the LED colours:

be supported by some controllers. To make sure

- VIOLET - Z-Wave network range tester

- YELLOW - sensor reset.

your Z-Wave network controller supports the Fibaro

Motion Sensor, get in touch with its manufacturer.

XIII. Z-WAVE RANGE TEST

Motion, temperature and light intensity values are presented in

The Fibaro Motion Sensor has a built in Z-Wave network main

controller's range tester. Follow the below instructions to test the

Home Center 2 menu with the following icons:

main controller's range:

1) Press and hold the B-button for 2 to 4 seconds until the LED glows

violet.

2) Release the B-button.

3) Press the B-button again, briefly.

4) LED will indicate the Z-Wave network's range (range signaling

modes described below).

5) To exit Z-Wave range test, press the B-button breifly.

Z-Wave range tester signaling modes:

LED indicator pulsing green - Fibaro Motion Sensor attempts to

extablish a direct communication with the main controller. If a direct

communication attempt fails, sensor will try to establish a routed

communication, through other modules, which will be signaled by

LED indicator pulsing yellow.

LED indicator glowing green - Fibaro Motion Sensor communica-

tes with the main controller directly.

LED indicator pulsing yellow - Fibaro Motion Sensor tries to

establish a routed communication with the main controller through

other modules (repeaters).

LED indicator glowing yellow - Fibaro Motion Sensor communica-

tes with the main controller through the other modules. After 2

seconds the sensor will retry to establish a direct communication

IX. ASSOCIATIONS

with the main controller, which will be signaled with LED blinking in

green.

LED indicator pulsing violet - Fibaro Motion Sensor does

By using association with Fibaro's devices the Fibaro Motion Sensor

communicate at the maximum distance of the Z-Wave network. If

may control another Z-Wave network device, e.g. a Dimmer, Relay

connection proves successful it will be confirmed with a yellow glow.

Switch, Roller Shutter, RGBW Controller, Wall Plug, or a scene

It's not recommended to use the sensor at the range limit.

(scene only through the Home Center 2 main controller).

LED indicator glowing red - Fibaro Motion Sensor is not able to

connect to the main controller directly or through another Z-Wave

NOTE

network device (repeater).

Association

allows

for

direct

communication

between Z-Wave network devices. Main controller

XIV. BATTERY USAGE TIPS

does not take part in such communication. Using this

mechanism, Fibaro Motion Sensor may

The Fibaro Motion Sensor's battery life is approximately 2 years at

communicate with other devices even when the

factory default settings. The current battery level is displayed in a

main controller is damaged, e.g. in case of a fire.

Home Center 2 interface. Red battery icon means the battery needs

replacement. In order to avoid tamper detection while replacing the

Fibaro Motion Sensor allows for the association of three groups.

battery, remove association of the 2-nd association group and

1st Association Group is assigned to the device status - sending

reduce tamper sensitivity (parameter 20 value set to 0). If battery

the BASIC SET control frame to the associated devices having

discharges quickly, please check for the following conditions which

detected motion.

may result in reducing the battery life:

2nd Association Group is assigned to the tamper alarm. Alarm

- Wake up interval is too short - it's recommended to lengthen the

frame will be sent to the associated devices once tampering is

interval.

detected.

- Temperature and light intensity reports are sent too frequently -

3rd Association Group reports the device status and allows for

modify the advanced configuration settings to decrease the

assigning a single device only (the main controller by default - the

frequency.

device reports its status to the main controller). It's not recommen-

- If associated devices or the Z-Wave network main controller are

ded to modify this association group.

disconnected from the power source it will cause the sensor to

frequently attempt to reconnect to those devices which will result in

The Fibaro Motion Sensor allows for controlling 5 regular and 5

shortening the battery life.

multichannel devices per an association group, out of which 1 field is

reserved for the Z-Wave network main controller.

X. EARTHQUAKE DETECTOR MODE

Fibaro Motion Sensor can be configured to work as a simple

earthquake detector, by setting the Parameter 24 value to 4. Reports

with scale of the vibrations (dimensionless) will be sent at the time

intervals specified in Parameter 22. First report will be sent

immediately after vibrations have been detected. The minimum

value of the vibrations, resulting in report being sent, can be defined

in Parameter 20. Once the vibrations cease, reports will stop being

sent. The Home Center 2 menu presents the earthquake detector

measurements in the following way:

NOTE

The Fibaro Motion Sensor is a battery-powered

device. Using batteries other than specified may

result in explosion. Dispose of properly, observing

environmental protection rules.

NOTE

The Fibaro Motion Sensor features remote software

updates. The functionality is supported by the Fibaro

Home Center 2 and may not be supported by other

controllers. During the software update process, the

sensor does NOT support alarm functions.