FIBARO FGMS-001-USA-A-V1.01 Operating Manual
Browse online or download pdf Operating Manual for Accessories FIBARO FGMS-001-USA-A-V1.01. FIBARO FGMS-001-USA-A-V1.01 2 pages. Motion sensor
Print Page
USA
© 2014 Fibar Group Sp. z o.o. All rights reserved.
Distributed by Fibaro
1040 East Lake Ave, Glenview, IL 60025, USA
www.fibaro.com
I. Z-WAVE NETWORK INCLUSION
The Fibaro Motion Sensor can be included into the Z-Wave network
by using the B-button.
1) Open the sensor's casing.
2) Unlock battery by removing "I'm ready" stripe.
3) Make sure the device is located within direct range of main
controller.
4) Set the main controller into learning mode (see main controller's
operating manual).
5) Quickly, triple click the B-button - LED diode will glow blue.
6) Fibaro Motion Sensor will be detected and included into the
Z-Wave network. Wait for the main controller to configure the sensor.
7) If necessary, wake up the Motion Sensor by triple clicking the
B-button. LED diode will glow blue to confirm the sensor wake up.
8) Close the sensor's casing. Enclosure lock is marked with dots.
OPERATING MANUAL
FIBARO MOTION SENSOR
FGMS-001-USA-A-V1.01
The Fibaro Motion Sensor is a universal Z-Wave multi-sensor. Along
with detecting motion the device measures the temperature and light
intensity. The sensor has a built-in accelerometer to detect any
tampering of the device. The Fibaro Motion Sensor is battery powe-
red device and designed to be installed quickly and easily on any
surface. The LED indicator signals motion, temperature level, opera-
ting mode and can be used to see if device is within the Z-Wave
network. The motion sensor can be used for lighting scenes and
pressence monitoring systems.
SPECIFICATIONS
Diagram 1 - B-button.
Power Supply:
CR123A battery, 3.0V DC
II. EXCLUDING SENSOR FROM THE Z-WAVE NETWORK
Recommended installation height:
2.4m
1) Make sure the sensor's battery is unlocked.
Operational Temperature:
0-40
o
C
2) Set the main controller into learning mode (see main controller's
operating manual)
Measured Temperature Range:
-20 to 100
C
3) Quickly, triple click the B-button, located inside Fibaro Motion
o
Sensor's casing.
4) LED diode will glow blue confirming that the device has sent the
Temperature Measuring
0.5
C (within 0
C-40
C range)
o
o
o
Node Info Z-Wave command frame.
Accuracy:
III. SENSOR INSTALLATION
Light Intensity Measuring Range:
0-32000 LUX
1) Include the device into the Z-Wave network (see p.II). Note that
the inclusion process may be performed ONLY in direct range of the
Radio Protocol:
Z-Wave
main controller.
2) Install the sensor's holder in desired location.
3) If the sensor is already included in the Z-Wave network, wake it up
Radio Frequency:
869 MHz EU;
by triple clicking the B-button.
908 MHz US;
4) Insert the Motion Sensor in its holder.
921 MHz ANZ;
869 MHz RU;
5) Test the sensor's operation - check whether the LED diode
indicates motion detection.
6) Test the Z-Wave network assuring the device is within range.
Range:
up to 50 m outdoors
up to 30 m indoors
(depending on terrain and
building structure)
TECHNICAL INFORMATION
- Compatible with any Z-Wave controller.
- Detects motion using a passive IR sensor.
- Measures the temperature.
- Measures the light intensity.
- Easy installation on a wall or any surface.
- Protected against tampering and theft - once vibrations are
detected, the notification is sent to the main controller.
- Alarms of movement and temperature are signaled by LED diode
blinking.
- Simple earthquake detector mode.
CAUTION
Read this manual before attempting to install the
Diagram 2 - Motion detector, light sensor, LED diode.
device.
Failure
to
observe
recommendations
!
included in this manual may be dangerous or cause
a violation of the law. The manufacturer, Fibar Group
DICTIONARY:
Sp. z o.o., will not be held responsible for any loss or
• INCLUSION (Adding) - a device sends "Node Info" command
damage resulting from not following the instructions
frame which allows it to be included into existing Z-Wave network.
of operating manual.
The Inclusion process is started by setting the main controller into
Learning Mode and pressing the B-button 3 times. After Node Info
command frame has been sent a device waits 5 seconds to receive
CAUTION
Z-Wave command frames from the main controller.
Work within local code height requirements for
• EXCLUSION (Removing) - removing a device from the existing
!
installation of the Fibaro Smoke Sensor. Take
Z-Wave network
special precautions during installation and use tools
• ASSOCIATION - controlling other devices within the Z-Wave
and equipment in perfect working order. It's
network
recommended to observe ladders, lifts and other
• MULTI-CHANNEL ASSOCIATION - controlling other multi-channel
obstacles.
devices within the Z-Wave network
CAUTION
When handled carelessly or used in non-specified
!
environment conditions, the device may not function
properly. It's highly recommended to take all safety
precautions
to
ensure
safety
and
property
protection.
B-BUTTON
Diagram 3 - preparing Fibaro Motion Sensor for operation.
SENSOR
Diagram 4 - Fibaro Motion Sensor installation.
Diagram 5 - Fibaro Motion Sensor's proximity area.
IV. DETECTION AREA AND WORKING CONDITIONS
Fibaro Motion Sensor's detection area is shown in diagram #6.
Fibaro Motion Sensor has to be installed in a corner of the room or
perpendicularly to the doors.
Actual range of the sensor can be influenced by environment
conditions. Should false motion alarms be reported, check for any
moving objects within the sensor's detection area, such as trees
blowing in the wind, cars passing by, windmills. False motion alarms
may be caused by moving masses of air and heat as well. If the
device keeps on reporting false alarms, despite all of the
above-mentioned factors have been eliminated, install the device in
another place or adjust the advanced parameters.
3 m
0 m
7 m
5 m
0 m
5 m
STICKER
7 m
Diagram 6 - Fibaro Motion Sensor's motion detection area.
How to eliminate pet-triggered false alarms:
Fibaro Motion Sensor should be installed 2-3m above the floor,
pointed parallely to the floor level. If wandering pets trigger false
alarms it's recommended to modify parameters 1 and 3 settings. The
value of parameter 1 can depend on pet's size and environment
conditions. It's good to experiment with settings, increasing the
parameter value by 5 at each attempt until the desired effect is
reached. If parameter 1 settings modifications will not produce
satisfactory results, it's recommended to experiment with parameter
3 settings (pulse counter), increasing its value.
V. INSTALLATION NOTES
IX. EARTHQUAKE DETECTOR MODE
Fibaro Motion Sensor can be configured to work as a simple
Fibaro Motion Sensor cannot be pointed at any source of heat (e.g.
earthquake detector, by setting the Parameter 24 value to 4. Reports
radiators, fireplaces, cookers, etc.) or at any source of light (direct
with scale of the vibrations (dimensionless) will be sent at the time
sunlight, lamps).
intervals specified in Parameter 22. First report will be sent
It's not recommended to install the motion sensor in places prone to
immediately after vibrations have been detected. The minimum
drafts. Sensor can be mounted using screw or the sticker.
value of the vibrations, resulting in report being sent, can be defined
in Parameter 20. Once the vibrations cease, reports will stop being
sent. The Home Center 2 menu presents the earthquake detector
VI. RESETTING THE FIBARO MOTION SENSOR
measurements in the following way:
The Fibaro Motion Sensor reset erases the memory, including all
information on the Z-Wave network and the main controller.
Fibaro Motion Sensor reset procedure:
1) Make sure the battery works and is in place.
2) Press and hold the B-button for 4-6 seconds until the LED glows
yellow signaling the 2nd option of the menu mode.
3) Release the B-button.
4) Again, press the B-button briefly.
Successful reset will be confirmed with the LED changing colour to
red and fading.
X. SENSOR'S ORIENTATION IN SPACE
NOTE
i
Device reset will not remove it from the Z-Wave
network
main
controller's
memory.
However,
The Fibaro Motion Sensor has a built-in accelerometer. When the
value of parameter 24 is set to 2 or 3, Z-Wave network controller will
removing the device from the Z-Wave network will
be informed on the Sensor's orientation in space.
reset Fibaro Motion Sensor automatically.
XI. LED VISUAL INDICATORS AND SETTINGS
VII. OPERATING WITHIN THE Z-WAVE NETWORK
The Fibaro Motion Sensor is equipped with a LED diode for
indicating sensor's operating modes and alarms. In addition the LED
Fibaro Motion Sensor has a built in motion detector, temperature
indicator may inform of the Z-Wave network range and the current
sensor and light intensity sensor, which make it a multi-channel
temperature.
device. In the Home Center 2 menu it will be presented as three
devices, depending on the main controller software version.
LED indicator modes:
1) Motion Alarm's colour will vary depending on the temperature. The
colour and the signaling mode can be set in parameter 80.
NOTE
2) Tamper alarm is signaled with an alternating blinking in red - blue
Fibaro
Motion
Sensor
capabilities
will
vary
- white.
i
depending on the Z-Wave network controller. Certain
3) The Z-Wave Node Info command frame is signaled with glowing
functionalities of the Fibaro Motion Sensor may not
in blue.
be supported by some controllers. To make sure
your Z-Wave network controller supports the Fibaro
To enter MENU press and hold the B-button for 3 seconds. MENU
Motion Sensor, get in touch with its manufacturer.
levels will be signaled with the LED colours:
- VIOLET - Z-Wave network range tester
- YELLOW - sensor reset.
Motion, temperature and light intensity values are presented in
Home Center 2 menu with the following icons:
XII. Z-WAVE RANGE TEST
The Fibaro Motion Sensor has a built in Z-Wave network main
controller's range tester. Follow the below instructions to test the
main controller's range:
1) Press and hold the B-button for 2 to 4 seconds until the LED glows
violet.
2) Release the B-button.
3) Press the B-button again, briefly.
4) LED will indicate the Z-Wave network's range (range signaling
modes described below).
5) To exit Z-Wave range test, press the B-button briefly.
Z-Wave range tester signaling modes:
LED indicator pulsing green - Fibaro Motion Sensor attempts to
establish a direct communication with the main controller. If a direct
communication attempt fails, sensor will try to establish a routed
communication, through other modules, which will be signaled by
LED indicator pulsing yellow.
LED indicator glowing green - Fibaro Motion Sensor communica-
tes with the main controller directly.
LED indicator pulsing yellow - Fibaro Motion Sensor tries to
establish a routed communication with the main controller through
VIII. ASSOCIATIONS
other modules (repeaters).
LED indicator glowing yellow - Fibaro Motion Sensor communica-
tes with the main controller through the other modules. After 2
By using association with Fibaro's devices the Fibaro Motion Sensor
seconds the sensor will retry to establish a direct communication
may control another Z-Wave network device, e.g. a Dimmer, Relay
Switch, Roller Shutter, RGBW Controller, Wall Plug, or a scene
with the main controller, which will be signaled with LED blinking in
green.
(scene only through the Home Center 2 main controller).
LED indicator pulsing violet - Fibaro Motion Sensor does
communicate at the maximum distance of the Z-Wave network. If
NOTE
connection proves successful it will be confirmed with a yellow glow.
Association
allows
for
direct
communication
It's not recommended to use the sensor at the range limit.
i
between Z-Wave network devices. Main controller
LED indicator glowing red - Fibaro Motion Sensor is not able to
does not take part in such communication. Using this
connect to the main controller directly or through another Z-Wave
mechanism, Fibaro Motion Sensor may communica-
network device (repeater).
te with other devices even when the main controller
is damaged, e.g. in case of fire.
XIII. BATTERY USAGE TIPS
Fibaro Motion Sensor allows for the association of three groups.
The Fibaro Motion Sensor's battery life is approximately 2 years at
1st Association Group is assigned to the device status - sending
factory default settings. The current battery level is displayed in a
the BASIC SET control frame to the associated devices having
Home Center 2 interface. Red battery icon means the battery needs
detected motion.
replacement. In order to avoid tamper detection while replacing the
2nd Association Group is assigned to the tamper alarm. Alarm
battery, remove association of the 2-nd association group and
frame will be sent to the associated devices once tampering is
reduce tamper sensitivity (parameter 20 value set to 0). If battery
detected.
discharges quickly, please check for the following conditions which
3rd Association Group reports the device status and allows for
may result in reducing the battery life:
assigning a single device only (the main controller by default - the
- Wake up interval is too short - it's recommended to lengthen the
device reports its status to the main controller). It's not recommen-
interval.
ded to modify this association group.
- Temperature and light intensity reports are sent too frequently -
modify the advanced configuration settings to decrease the
The Fibaro Motion Sensor allows for controlling up to five regular and
frequency.
up to five multi-channel devices per an association group. However
- If associated devices or the Z-Wave network main controller are
the 3rd association group is recommended for the Z-Wave network
disconnected from the power source it will cause the sensor to
main controller (e.g. Fibaro Home Center 2).
frequently attempt to reconnect to those devices which will result in
shortening the battery life.