FIBARO RGBW Controller Operating Manual - Page 2

Browse online or download pdf Operating Manual for Controller FIBARO RGBW Controller. FIBARO RGBW Controller 2 pages.

Print Page

12/24VDC

GND

IN1

IN2

IN3

IN4

Fig. 6- Terminals description

12/24 VDC

Adapter

Fig. 7 - Connecting halogen lighting

12/24 VDC

Adapter

Wind

Temperature

Humidity

Light

Sensor

Fig. 8 - 0-10 V sensors wiring diagram

12/24 VDC

230V AC

Adapter

12V

Fig. 9 - RGBW strip wiring diagram

12/24 VDC

230V AC

Adapter

0-10V

12V

Fig 10. - RGBW strip with 0-10 V potentiometer wiring diagram

NOTES FOR THE DIAGRAM

IN3 - potential free / 0-10V input 3

IN4 - potential free / 0-10V input 4

12/24VDC - power supply signal

R - output assigned to IN1

GND - power supply ground signal

G - output assigned to IN2

IN1 - potential free / 0-10V input 1

B - output assigned to IN3

IN2 - potential free / 0-10V input 2

W - output assigned to IN4

XIII Advanced configuration

GENERAL:

1. ALL ON / ALL OFF function activation

Default setting: 255

0 - ALL ON inactive, ALL OFF inactive

1 - ALL ON inactive, ALL OFF active

2 - ALL ON active, ALL OFF inactive

255 - ALL ON active, ALL OFF active

FIBARO

Parameter size: 1 [byte]

RGBW

6. Associations command class choice

Default setting: 0

CONTROLLER

0 - NORMAL (DIMMER) - BASIC SET/SWITCH_MULTILEVEL_-

START/STOP

1 - NORMAL (RGBW) - COLOR_CONTROL_SET/STAR-

T/STOP_STATE_CHANGE

2 - NORMAL (RGBW) - COLOR_CONTROL_SET

3 - BRIGHTNESS - BASIC SET/SWITCH_MULTILEVEL_STAR-

T/STOP

4 - RAINBOW (RGBW) - COLOR_CONTROL_SET

Parameter size: 1 [byte]

IN/OUT:

8. Outputs state change mode

Default setting: 0

0 - MODE1 (related parameters: 9-step value, 10-time between

steps)

1 - MODE2 (related parameters: 11-time to change value, relevant

for RGB/RGBW)

12V

Parameter size: 1 [byte]

GND

MODE1

IN1

Example: change saturation level from 0% to 99%

FIBARO

IN2

Parameter 9: Step = 5

IN3

RGBW

Parameter 10: Time between steps: 10ms

IN4

CONTROLLER

9. Step value (relevant for MODE1)

Red

Default setting: 1

Green

Available settings: 1 - 255

Blue

Parameter size: 1[byte]

White

10. Time between steps (relevant for MODE1)

Default setting: 10 (10ms)

0 - immediate change of state

1-60000 - (1-60000 ms)

MODE2

Example: change saturation level from 0% to 99%

Parameter 11: time for changing from start to end value = 500sec

11. Time for changing from start to end value

Default setting: 67 (3s)

0 - immediate change

1-63 - 20-126- [ms] value*20ms

12V

65-127 - 1-63 [s] [value-64]*1s

GND

129-191 - 10-630[s] [value-128]*10s

IN1

193-255 - 1-63[min] [value-192]*1min

IN2

FIBARO

Parameter size: 1[byte]

IN3

RGBW

IN4

12. Maximum brightening level

CONTROLLER

Red

Default setting: 255

Green

Available settings: 3-255

Blue

Parameter size: 1[byte]

White

13. Minimum dim level

Default setting: 2

Available settings: 3-255

Parameter size: 1[byte]

14. Inputs / Outputs configuration - relevant for main

controllers other than Home Center 2 only

12V

Default setting: 4369 Controlled device: RGBW, toggle switch

GND

inputs (NORMAL MODE)

IN1

Each 4bit refer to given IN/OUT (channel) settings

FIBARO

IN2

IN3

RGBW

IN4

CONTROLLER

Note

Red

The maximum leven cannot be lower than

minimum level.

Green

Blue

White

Channel 1

Channel 2

Channel 3

(4 bit)

0000

....

12V

1111

GND

IN1

If RGB/RGBW mode is chosen, settings for all 4 channels are

FIBARO

IN2

identical. Settings marked with X are forbidden and cannot be sent

IN3

RGBW

to the module.

IN4

CONTROLLER

Input type:

Red

- ANALOG - sensor with analog, 0-10V interface. Impossible to

Green

control from main controllers interface.

Blue

- MOMENTARY - momentary switch,

White

- TOGGLE - toggle switch,

- TOGGLE W/MEMORY - toggle switch (ON active for closing

switch terminals; OFF active for opening switch terminals)

Input operating mode (controlled with switch keys):

- NORMAL - each given switch key assigned to one output

channel,

- BRIGHTNESS - all of the channels are controlled together,

- RAINBOW - transition through all colours spectrum (operates on

3 RGB channels only)

Parameter size: 2[byte]

Settings available for single channel

LSB Controlled

MSB

device

(RGBW)

(NORMAL MODE)

(RGBW)

(BRIGHTNESS MODE)

(RGBW)

(RAINBOW MODE)

(RGBW)

(NORMAL MODE)

(RGBW)

(BRIGHTNESS MODE)

TOGGLE W. MEMORY

(RGBW)

(NORMAL MODE)

TOGGLE W. MEMORY

(RGBW)

(BRIGHTNESS MODE)

(IN)

(OUT)

(NORMAL MODE)

(OUT)

(NORMAL MODE)

(OUT)

TOGGLE W/MEMORY

(OUT)

(NORMAL MODE)

(OUT)

Note!

Parameter

settings, for controllers other than

Home Center 2, are available under

the following link:

http://manuals.fibaro.com/

ras-rgbw-controller-en.pdf

16. Memorize device status at power cut. Device will be set to

status memorized before power cut.

Default setting: 1

0 - device does not memorize its status at the power cut. Load is

disconnected.

1 - device memorizes its status at the power cut. Load will be set

to the status from before power cut (parameters, current outputs

status, energy)

Parameter size: 1[byte]

ALARM:

30. Alarm of any type (general alarm, flood alarm, smoke

alarm: CO, CO2, temperature alarm).

Default setting: 0

0 - INACTIVE - the device doesn't respond to alarm frames

1 - ALARM ON - the device turns on once alarm is detected (all

channels set to 99%)

2 - ALARM OFF - the device turns off once alarm is detected (all

channels set to 0%)

3 - ALARM PROGRAM - alarm sequence turns on (program

selected in parameter 38)

Parameter size: 1[byte]

38. Alarm sequence program

Default setting: 10

1 - 10 (1-10 specifies alarm program number)

Parameter size: 1[byte]

39. Active PROGRAM alarm time

Default setting: 600

1-65534 (1s-65534s)

Parameter size: 2[byte]

Channel 4

REPORTS:

(4 bit)

42. Command class reporting Outputs status change

0000

Default setting: 0

....

0 - reporting as a result of inputs and controllers actions (SWITCH

1111

MULTILEVEL)

1 - reporting as a result inputs actions (SWITCH MULTILEVEL)

2 - reporting as a result of inputs actions (COLOR CONTROL)

Parameter size: 1[byte]

43. Reporting 0-10v analog inputs change threshold.

Parameter defines a value by which input voltage must change in

order to be reported to the main controller. New value is calculated

based on last reported value:

Default setting: 5 (0,5V)

1-100 - (0,1 - 10V)

Parameter size: 1[byte]

44. Power load reporting frequency (if last reported value differs

from the current value). Reports will also be sent in case of polling.

Default setting: 30 (30s)

1 - 65534 (1s-65534s) - time between reports,

0 - reports are not sent. Reports will only be sent in case of polling

or at turning OFF the device.

Parameter size: 2[byte]

45. Reporting changes in energy consumed by controlled

devices. New, reported energy value is calculated based on last

reported value.

Default setting: 10 (0,1 kWh)

1 - 254 (0,01kWh - 2,54kWh)

0 - changes in consumed energy will not be reported. Reports will

be sent only in case of polling.

Parameter size: 1[byte]

OTHER:

MOMENTARY

71. Response to BRIGHTNESS set to 0%

Default setting: 1

MOMENTARY

0 - illumination colour set to white (all channels controlled together)

1 - last set colour is memorized

MOMENTARY

Parameter size: 1[byte]

72. Starting predefined program when device set to work in

TOGGLE

RGB/RGBW mode (parameter 14) - relevant for main

controllers other than Home Center 2 only.

TOGGLE

Default setting: 1

1-10 animation program number

Parameter size: 1[byte]

73. Triple click action

Default setting: 0

0 - NODE INFO control frame is sent,

ANALOG 0-10V

1 - starting favourite program

(SENSOR)

Parameter size: 1[byte]

MOMENTARY

TIPS FOR ARRANGING THE ANTENNA:

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

TOGGLE

order to prevent interferences.

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door frames)

may impair signal reception!

Do not cut or shorten the antenna - its length is

perfectly matched to the band in which the system

recommended

operates

EPILEPSY WARNING:

Stroboscope effect and rapid light changes may

potentially

trigger

seizures

for

people

photosensitive epilepsy!

XIX. GUARANTEE

1. FIBAR GROUP S.A. with its registered office in Poznan, ul.

Lotnicza 1, 60-421 Poznań, entered into the Register of

Entrepreneurs of the National Court Register maintained by the

District Court for Poznań-Nowe Miasto and Wilda in Poznań, VIII

Commercial Division of the National Court Register (KRS) under

number: 553265, NIP 7811858097, REGON: 301595664, share

capital PLN 1,182,100 paid in full, other contact information is

available at: www.fibaro.com (hereinafter "the Manufacturer")

guarantees that the device sold (hereinaftr: "the Device" is free from

material and manufacturing defects.

2. The Manufacturer shall be responsible for malfunctioning of the

Device resulting from physical defects inherent in the Device that

cause its operation to be incompatible with the specifications within

the period of:

- 24 months from the date of purchase by the consumer,

- 12 months from the date of purchase by a business customer (the

consumer and business customer are further collectively referred to

as "Customer").

3. The Manufacturer shall remove any defects revealed during the

guarantee period, free of charge, by repairing or replacing (at the

sole discretion of the Manufacturer) the defective components of the

Device with new or regenerated components. The manufacturer

reserves the right to replace the entire Device with a new or

regenerated device. The Manufacturer shall not refund money paid

for the device.

4. Under special circumstances, the Manufacturer may replace the

Device with a different device most similar in technical characteristics.

5. Only the holder of a valid guaranty document shall be entitled to

make claims under guarantee.

6. Before making a complaint, the Manufacturer recommends using

the telephone or online support available at https://www.fibaro.com/-

support/.

7. In order to make a complaint, the Customer should contact the

Manufacturer via the email address given at https://www.fibaro.com/-

support/.

8. After the complaint has been properly filed, the Customer will

receive contact details for the Authorized Guarantee Service

("AGS"). The customer should contact and deliver the Device to

AGS. Upon receipt of the Device, the manufacturer shall inform the

Customer of the return merchandise authorization number (RMA).

9. Defects shall be removed within 30 days from the date of

delivering the Device to AGS. The guarantee period shall be

extended by the time in which the Device was kept by AGS.

10. The faulty device shall be provided by the Customer with

complete standard equipment and documents proving its purchase.

11. The cost of transporting the Device in the territory of the Republic

of Poland shall be covered by the Manufacturer. The costs of the

Device transport from other countries shall be covered by the

Customer. For unjustified complaints, AGS may charge the

Customer with costs related to the case.

12. AGS shall not accept a complaint claim when:

- the Device was misused or the manual was not observed,

- the Device was provided by the Customer incomplete, without

accessories or nameplate,

- it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

- the guarantee document is not valid or there is no proof of

purchase,

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abrasions, physical

deformations caused by impact, falling or dropping the device or

other object, improper use or not observing the operating manual);

- damages resulting from external causes, e.g.: flood, storm, fire,

lightning, natural disasters, earthquakes, war, civil disturbance, force

majeure, unforeseen accidents, theft, water damage, liquid leakage,

battery spill, weather conditions, sunlight, sand, moisture, high or low

temperature, air pollution;

- damages caused by malfunctioning software, attack of a computer

virus, or by failure to update the software as recommended by the

Manufacturer;

- damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

- damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

- damages caused by using accessories not recommended by the

Manufacturer

- damages caused by faulty electrical installation of the Customer,

including the use of incorrect fuses;

- damages caused by Customer's failure to provide maintenance and

servicing activities defined in the operating manual;

- damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

- defects caused by operating faulty Device or accessories.

14. The guarantee shall not cover natural wear and tear of the Device

and its components listed in the operating manual and in technical

documentation as such elements have a defined operational life.

15. The Device Guarantee shall not exclude, limit or suspend the

Customer's warranty rights.

16. The Manufacturer shall not be liable for damages to property

caused by defective device. The Guarantor shall not be liable for

indirect, incidental, special, consequential or punitive damages, or

for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any other damages

arising from or related to the use of the Device.

Simplified EU declaration of conformity:

Hereby, Fibar Group S.A. declares that the device is in compliance

with Directive 2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet address:

www.manuals.fibaro.com

WEEE Directive Compliance:

Device labelled with this symbol should not be disposed with other

household wastes. It shall be handed over to the applicable

collection point for the recycling of waste electrical and electronic

equipment.

with

Attention!

This product is not a toy. Keep away from children and animals!

This device complies with Part 15 of the FCC Rules

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including

interference that may cause undesired operation. This equipment

has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada license-exempt RSSs.

Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired

operation of the device.

Cet appareil est conforme aux normes d'exemption de licence RSS

d'Industry Canada. Son fonctionnement est soumis aux deux

conditions suivantes: (1) cet appareil ne doit pas causer d'interféren-

ce et (2) cet appareil doit accepter toute interférence, notamment les

interférences qui peuvent affecter son fonctionnement.

Note

Changes and modifications not expressly approved by the

manufacturer or registrant of this equipment can void your authority

to operate this equipment under Federal Communications

Commission's rules.

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.