Sharp Carousel R-326FS Service Manual - Page 30

Browse online or download pdf Service Manual for Microwave Oven Sharp Carousel R-326FS. Sharp Carousel R-326FS 44 pages. Sharp operation manual microwave oven r-326fs
Also for Sharp Carousel R-326FS: Operation Manual (24 pages)

Print Page

R - 326FS

CAUTION: 1. DISCONNECT OVEN FROM POWER SUP

PLY BEFORE REMOVING OUTER CASE.

2. DISCHARGE THE HIGH VOLTAGE CAPACI-

TOR BEFORE TOUCHING ANY OVEN COM-

PONENTS OR WIRING.

1. Disconnect the power supply cord and then remove

outer case.

2. Open the oven door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect wire leads (primary) from power transformer

and the filament leads and high voltage wire from the

magnetron and capacitor terminals.

5. Remove four (4) screws holding transformer to bottom

plate.

6. Remove transformer from bottom plate.

1. Disconnect the power supply cord, and then remove outer

case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Open covers of the terminal insulator by using small flat type

screw driver.

5. Remove the receptacle from the terminal insulator.

6. Now, the terminal insulator is free.

Terminal

insulator

HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

1. Disconnect the power supply cord and then remove outer

case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the high voltage wire of the power transformer

from the high voltage capacitor.

5. Disconnect the high voltage wire of high voltage rectifier

assembly from the magnetron.

6. Disconnect the filament lead (short one) of the power

transformer from the high voltage capacitor.

7. Remove two (2) screws holding capacitor holder to oven

R emoval

1. Disconnect the power supply cord and then remove outer

case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect all wire leads from magnetron.

5. Remove the five (5) screws holding chassis support to

magnetron, oven cavity back plate, oven cavity front flange

and fan duct.

6. Remove the chassis support from oven.

7. Carefully remove the four (4) screws holding magnetron to

waveguide flange.

8. Lift up magnetron with care so that magnetron antenna is

POWER TRANSFORMER REMOVAL

TERMINAL INSULATOR REPLACEMENT

Flat type

screw driver

MAGNETRON REMOVAL

NOTE: When replacing the outer case, the 2 special

Torx screws must be reinstalled in the same

locations.

Reinstallation

1. Rest transformer on the bottom plate with its primary

terminals toward the oven face plate.

2. Secure transformer with four screws to bottom plate.

3. Reconnect wire leads (primary) to power transformer and

filament leads and high voltage wire of transformer to

magnetron and high voltage capacitor. Refer to "PICTORIAL

DIAGRAM" .

4. Reinstall outer case and check that oven is operating

properly.

Installation

1. Insert the receptacle into terminal insulator.

2. Close covers of the terminal insulator, as shown below.

3. Reconnect all leads removed from components during testing.

4. Reinstall the outer case (cabinet).

5. Reconnect the power supply cord after the outer case is installed.

6. Run the oven and check all functions

Covers

Receptacle

cavity rear plate.

8. Remove one (1) screw holding high voltage rectifier

assembly to capacitor holder.

9. Disconnect rectifier terminal from capacitor.

High voltage rectifier assembly is now free.

10. Remove capacitor holder. Capacitor is now free.

CAUTION: WHEN REPLACING HIGH VOLTAGE RECTI-

FIER AND HIGH VOLTAGE CAPACITOR,

GROUND SIDE TERMINAL OF THE HIGH VOLT-

AGE RECTIFIER MUST BE SECURED FIRMLY

WITH A GROUNDING SCREW.

not hit by any metal object around antenna.

9. Now, the magnetron is free.

Reinstallation

1. Reinstall the magnetron to waveguide flange with the four

(4) screws.

2. Insert the two (2) tabs of the chassis support to the oven

cavity front plate and the back plate.

3. Hold the chassis support to the oven cavity back plate, oven

cavity front flange, magnetron and the fan duct with the five

(5) screws.

4. Reconnect the wire leads to the magnetron and thermal cut-

out (MG). Refer to "PICTORIAL DIAGRAM"