Sharp AR-C262M Key Key Operator's Manual - Page 17
Browse online or download pdf Key Operator's Manual for All in One Printer Sharp AR-C262M Key. Sharp AR-C262M Key 20 pages. Digital full colour multifunctional system
Also for Sharp AR-C262M Key: Driver Installation (28 pages)
Print Page
Exposure adjustment
Use this program to lighten or darken copies in the
automatic exposure mode. The factory setting is "5".
"1" indicates lighter density and "9" indicates darker
density on the touch panel.
Rotation copy setting
If this program is set, the image of originals will rotate
when the orientation of the originals does not match
that of the copy paper.
(Rotation copy will function only if the auto paper select
or auto image mode has been selected.)
NOTE
For copying from A5 or 5-1/2" x 8-1/2" size originals
onto A5R or 5-1/2" x 8-1/2"R paper, this program
must be set.
Add or change extra preset ratios
When using AB sizes, there are normally five preset
enlargement ratios and five preset reduction ratios.
When using inch sizes, there are normally four preset
enlargement ratios and four preset reduction ratios.
This program allows you to add two more preset
enlargement ratios and two more preset reduction
ratios. This program also allows you to change a preset
ratio.
NOTE
Only an added preset ratio can be changed.
Initial margin shift setting
Set the initial margin shift value with this program.
The value can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
If an optional duplex module/2 x 500 sheet paper
drawer (AR-D19N) and duplex bypass/inverter unit
(AR-RB1) are not installed, the value for the reverse
side (side 2) is not displayed.
Erase width adjustment
Set the initial setting of the amount of the erase area
with this program.
The values can be set from 0 mm to 20 mm in 1 mm
increments or from 0" to 1" in 1/8" increments.
Setting a maximum number of copies
Use this program to limit the maximum number of
copies per copy run which can be input in the copy
quantity display.
A number from 1 to 999 can be set.
PROGRAMS FOR COPY MODE
Initial colour balance setting
Colour balance settings that have been adjusted using
the special "Colour Balance" function explained on
page 6-14 of the "Operation manual (for general
information and copier operation)" can be called up
and set as initial colour balance settings* by storing
them ahead of time in a job program (page 6-25 of the
"Operation manual (for general information and copier
operation)"). Use this feature when you want to
repeatedly use settings for a favorite colour or for
correction when a change occurs in the colour balance.
* Preset values displayed when you select the special
"Colour Balance" function. The factory default
settings are the "0" position for all eight levels of each
colour.
When the [INITIAL COLOUR BALANCE SETTING]
key is touched, the following display will appear.
KEY OPERATOR PROGRAMS
INITIAL COLOUR BALANCE SETTING
PRESS PROGRAM NUMBER IN WHICH COLOUR BALANCE PROGRAM IS REGISTERED.
1
2
6
7
RETURN TO THE FACTORY DEFAULT
SETTINGS.
If a job program number key is touched that does not
have colour balance settings, a warning message will
appear.
To return colour balance settings that have been
stored as initial settings to the factory default settings
(the "0" position for all eight levels of each colour),
touch the [RETURN TO THE FACTORY DEFAULT
SETTINGS.] key.
Auto colour calibration
The Auto Colour Calibration program enables
automatic colour gradation correction when the colour
reproduction is incorrect.
NOTE
The colour gradation may not be sufficiently
corrected after one correction cycle. If so, execute
the program again.
When the [AUTO COLOUR CALIBRATION] key is
touched, the following display will appear.
KEY OPERATOR PROGRAMS
AUTO COLOUR CALIBRATION
USE 11"X17" OR A3 PAPER FOR THIS ADJUSTMENT.
PRESS [EXECUTE] TO PRINT THE TEST PATCH.
OK
3
4
5
8
9
10
OK
EXECUTE
15