Sharp AR-M550U Key Operator's Manual - Page 14

Browse online or download pdf Key Operator's Manual for All in One Printer Sharp AR-M550U. Sharp AR-M550U 20 pages. Digital multifunctional system
Also for Sharp AR-M550U: Technical Manual (48 pages)

Print Page

GENERAL PROGRAMS

Saddle stitch position adjust

This program is used to adjust the stapling position

(folding position) when using the saddle stitch function

of the optional saddle stitch finisher.

The value can be adjusted in 0.25 mm increments

within ±2.00 mm from the reference position for each

paper size.

Max.+2mm

Position adjusted

to the plus

direction

Reference position

[AUTOMATIC SADDLE STITCH] checkmark

The saddle stitch print function can normally be divided

into the following three general steps.

1. The pages of the original are automatically

reordered to allow saddle stitch binding (saddle

stitch function).

2. The pages are folded at the centre.

3. The paper is stapled at the centre in two places

(saddle stitch stapling).

The [AUTOMATIC SADDLE STITCH] checkbox is

selected by default.

Selection of the checkbox assumes the use of the

above saddle stitch printing function (three steps).

Saddle stitch stapling exceptions

Depending on the purpose of saddle stitch stapling, it

may be necessary to perform saddle stitch stapling on

printed matter that has already been bound by saddle

stitching. In this case, it is necessary to disable step 1

above. If you frequently perform this type of

exceptional saddle stitch stapling that requires

disabling step 1, remove the checkmark from the

[AUTOMATIC SADDLE STITCH] checkbox.

Auto switching of finisher trays

Output to the upper tray of the saddle stitch finisher or

finisher normally stops if a large number of sheets

accumulates in the tray and the tray full sensor

activates. This program can be used to have output

automatically switched to the lower tray when this

happens so that printing can continue. To enable the

program,

select

the

FINISHER TRAYS" checkbox.

This setting is not effective when a tray other than the

upper tray of the saddle stitch finisher or finisher is set

as the output tray.

Min.-2mm

Position adjusted

to the minus

direction

"AUTO

SWITCHING

Rotated output

When Rotated output is turned on, you can have the

paper output orientation (A4-size paper only) of each

set of copies alternate between horizontal and vertical.

This function is used to sort output when neither the

Finisher peripheral nor the Saddle stitch finisher

peripheral are installed.

* To use this function, A4-size paper must be loaded

both horizontally and vertically in the paper trays. This

function works when paper is output to the centre tray.

The function does not work in the following cases:

• When paper is output to the Finisher peripheral or the

Saddle stitch finisher.

• Printing in Group mode.

• When a letter-size original is printed on A4-size

paper using the "A4/letter size auto change" key

operator program (page 5-5 of the "Operation

manual (for printer)").

• When "Transparency Inserts" or "Different Paper

settings" is selected in the printer driver.

• When the "Paper Source" drop down in the "Paper

Selection" is set to any selection other than "Auto

Select" in the printer driver.

• When the printing paper size for a stored job or a job in

progress has been overridden and changed to A4 size.

NOTE

When interrupt copying is performed, Rotated output

does not take place to distinguish the output of

regular copying from interrupt copying. Also,

Rotated output cannot be used to sort output by job.

Auto paper selection setting

Use this program to select the paper type* for which the

automatic

paper

selection

Selections are "PLAIN PAPER", "PLAIN AND

RECYCLE PAPER", and "RECYCLE PAPER".

* The paper type set for each paper tray in the paper

tray settings of the user settings (page 2-10 of the

"Operation manual (for general information and

copier operation)").

List print

This program is used to print lists and reports that can

only be printed from the key operator programs.

• Touch the [KEY OPERATOR PROGRAMS LISTS]

key to print one of the following groups:

Copy, printer, fax/image send, document filing,

general, security, all program lists

• Touch a key other than the [KEY OPERATOR

PROGRAMS LISTS] key to begin printing a list or report.

function

operates.