Ace FDT-63 Operating And Mounting Instructions - Page 3

Browse online or download pdf Operating And Mounting Instructions for Fire and Smoke Dampers Ace FDT-63. Ace FDT-63 4 pages. Rotary dampers

Print Page
Rotary Damper FDT (continuous rotation)
3
Mounting instructions and mounting accessories
Installation instructions
Before installation and use check whether the identification num-
ber on the product or on the packaging matches the respective
designation on the delivery note.
Rotary dampers are maintenance-free and ready-to-in-
stall.
WARNING
The specified rated damping torque
applies at a temperature of 23 °C or a
speed of 20 rpm. The damping torque can change depending
on the temperature or speed. Please observe the characteristic
curves in the mounting instructions.
The flap/mass can fall off during installation and removal
of the rotary damper. Secure moving flap/mass against falling
down!
Depending on the application, failure of the product could
lead to personal injuries and/or material damage. Use
additional safety elements.
Exceeding the permissible temperature range, the max.
speed, the cycle number and the specified damping torque
can lead to premature failure or destruction of the rotary
damper. Operating temperature range, speed of 50 rpm, cycle
number of
12/min. and the specified damping torque must be maintained.
Dirt, swarf and aggressive liquids can cause premature
failure of the rotary damper. Protect or encapsulate rotary
damper from external materials in the surrounding area.
Do not use rotary dampers in high-pressure or vacuum
range.
Construction size: Ø 47 mm to 70 mm
Max. speed: 50 rpm
Lifetime: 50,000 cycles (1 cycle = 360° left-hand,
360° right-hand), at least 80 % of the original damping torque
after this. The service life may be significantly higher or lower,
depending on the application.
Operating temperature range: -10 °C to +50 °C
Damping medium: Silicone oil
Material: Outer body: Steel; Output shaft sleeve: Nylon
Damping direction: Top view of the shaft left-hand (L) =
anticlockwise, right-hand (R) = clockwise.
Mounting: in any position
Mounting information: Secure brake at the mounting holes and
connect the part to be braked via a suitable shaft to the output
shaft sleeve. An external guide or support of the moved part is
recommended. Thanks to the flat design, numerous dampers can
be fitted in parallel to increase the damping torque.
No axial or radial forces may be introduced via the shaft. The
rotary axis was not designed for side loading (see diagrams).
Safety instructions: Do not use rotary dampers as supports.
Provide an external guide or support.
On request: Special designs available on request.
Stand 03.2021
21_22_0019 Issue 05.2022
Note! The rotary axes, square mounts or free-wheel
mounts are not designed for side loading.
Side loading
End loading
Angular offset
Misalignment
Packaging disposal: Please dispose of the transportation pack-
aging in an environmentally-friendly manner. Recycling packaging
materials saves raw materials and reduces waste. The packaging
materials do not contain any prohibited materials.
FDT
R
B
A
C
G
D
Ø
H
Performance data and dimensions
1
Damping torque
Damping direction
A
TYPES
Nm
mm
FDT-47
2.0 +/- 0.3
two-sided
65
FDT-57
4.7 +/- 0.5
two-sided
79
FDT-63
6.7 +/- 0.7
two-sided
89
FDT-70
8.7 +/- 0.8
two-sided
95
The indicated damping torques refer to a rotational speed of 20 rpm and an ambient temperature of 23 °C.
1
Characteristic curves
At 23 °C ambient temperature
12
10
8
6
4
2
0
rpm
0
10
20
30
40
50
ACE Stoßdämpfer GmbH · Postfach 1510 · D-40740 Langenfeld · T +49 (0)2173 - 9226-10 (Technik -20) · F +49 (0)2173 - 9226-19 · [email protected] · www.ace-ace.com
-0.02
C
-0.1
F
E
Ø
Ø
Recommended Drive
Shaft Size
B
C
D
E
F
G
H
mm
mm
mm
mm
mm
mm
mm
56
8
4.5
47
42.8
1.6
10.3
68
10
5.5
57
52.4
1.6
11.2
76
12.5
6.5
63
58.6
1.6
11.3
82
12.5
6.5
70
65.4
1.6
11.3
At 20 rpm speed
12
FDT-70
10
FDT-63
8
FDT-57
6
4
FDT-47
2
0
0
10
20
30
40
ACE Stoßdämpfer GmbH · www.ace-ace.com
R
J
Weight
mm
mm
kg
4.5
10
0.050
5.5
13
0.075
6.5
17
0.095
6.5
17
0.110
FDT-70
FDT-63
FDT-57
FDT-47
°C
50