Cisco WBP54G - Small Business Pro Wireless-G Bridge Quick Installation Manual

Browse online or download pdf Quick Installation Manual for Wireless Access Point Cisco WBP54G - Small Business Pro Wireless-G Bridge. Cisco WBP54G - Small Business Pro Wireless-G Bridge 2 pages. Bridge for phone adapters
Also for Cisco WBP54G - Small Business Pro Wireless-G Bridge: User Manual (50 pages)

Print Page
®
A Division of Cisco Systems, Inc.
Package Contents
• Wireless-G Bridge for Phone Adapters (with
Attached Combo-power/Ethernet Cable)
• CD-ROM with Setup Wizard and User Guide
• Quick Installation Guide
• Registration Card
2.4
GHz
Wireless-G
802.11g
Bridge for Phone Adapters
Wireless
Quick Installation
Model No.
WBP54G
Model No.
1
Set up and Connect the Bridge
The Setup Wizard will guide you
through the steps to configure
and connect the Bridge.
A
Insert the Setup CD-ROM
into your CD-ROM drive. The
Setup Wizard should run
automatically, and the
Welcome screen should
appear. If it does not, click
Start and choose Run. In
the field that appears, enter
D:\setup.exe (if "D" is the
B
letter of your CD-ROM
drive).
B
Click Click Here to Start on
the Welcome screen.
C
After reading the License
Agreement, click Next if you
agree, or click Cancel to
end the installation.
D
C
This screen will inform you
about which Linksys phone
adapters and IP phones
work with the Bridge. Make
sure your phone adapter or
IP phone is listed on-screen.
Click Next.
D
NOTE:
The power adapter for your
Linksys phone adapter or IP phone
will be used to power the Bridge.
E
You will use the PC running
this Setup Wizard to set up
the Bridge. Disconnect the
power jack from the back of
the Linksys phone adapter
or IP phone. (You will use this
power adapter to power the
Bridge.) If your network
router or this PC is in a
different room, disconnect
E
the power adapter from the
electrical outlet. Move the
power adapter and Bridge
to the room where your
router or PC is located.
Click Next.
F
Connect the power jack to
the Power port of the Bridge.
Then plug the power
F
adapter into an electrical
outlet.
Click Next.
G
You will use the
combination Ethernet
network and power cable
attached to the Bridge.
Connect the Ethernet
network cable of the Bridge
G
to an Ethernet network (LAN)
port of the router or PC. (Do
not use the power cable
NOTE:
If you connect the Bridge to a
now; you will use it later.)
router, make sure the Bridge and PC
running the Setup Wizard are
Make sure the Bridge's
connected to the Ethernet network
Ethernet LED is solidly lit or
(LAN) ports of the same router.
flashing. Click Next.
H
A list of all Bridges for Phone
Adapters that can be
detected by the Setup
Wizard will be displayed.
Select the Bridge you are
installing and click Next. If
the Bridge you want is not
displayed, click the Refresh
List button to search again.
I
H
This screen will display a list
of wireless networks that can
be detected. Select the
wireless network you want.
If the network you want is
not displayed, click the
Refresh List button to
search again.
To manually enter the SSID
I
of the network you want,
click the SSID radio button
and enter the SSID of your
IMPORTANT:
Some wireless
wireless network.
access points or routers do not
broadcast their status information. If
Click Next.
you do not see the network you
J
want, click the SSID radio button
Configure the wireless
and manually enter its SSID.
security settings. Select the
method your network is
using, WPA, WPA2,
WEP (128-Bit), or WEP (64-
Bit). Then proceed to the
appropriate instructions. If
you are not using wireless
security, select Disabled,
and proceed to step K.