Cisco TelePresence Installation Manual - Page 4
Browse online or download pdf Installation Manual for Conference System Cisco TelePresence. Cisco TelePresence 4 pages. Configuring a cisco unified communications
manager sip trunk with a cisco telepresence content server
Also for Cisco TelePresence: Brochure (4 pages), Specifications (7 pages), Administrator's Manual (27 pages), Quick Reference Manual (2 pages), Manual (24 pages), Installation Sheet (2 pages)
Print Page
Installing Cisco TelePresence System Profile 65" Presentation Unit
6
Mounting the two modules together
A.
Main system: Remove the top grille and open the top
cover.
B.
Main system: Remove the uppermost screw on the
monitor sides facing each other, using a 2.5 mm Allen
key and a 7 mm wrench. See illustration.
C.
Both systems: Remove the uppermost screw on the
bottom modules, using a 3 mm Allen key and a 7 mm
wrench.
D.
Move the units towards each other. Leave some
space for the joint profile.
E.
Level and align the systems: Use the screws inside
the bottom module to adjust and align the two
systems. See the instructions in step 7.
F.
Place the joint profile between the two systems.
g.
Connect bottom modules: On the main bottom
module, fasten the long M4 screw from the inside of
the module through the joint profile and to the nut
on the nut plate. Do the same from the inside of the
presentation unit bottom module.
h.
Connect the monitor: On the main monitor, fasten
the short M4 screw from the inside of the monitor
through the joint profile and to the nut on the nut
plate.
I.
If further adjustments are needed do this with the
adjustments screws inside the bottom module.
8
Unpacking the Monitor box and mounting the monitor to the base
A.
Carefully lift and place the monitor onto the base.
NOTE:
Requires 4
B.
Open the top cover.
persons and lifting straps
hEAvY
to lift.
AND
C.
Repeat step 6 b for the presentation unit.
BULKY
D.
If further adjustments are needed to align the systems,
REQUIRES:
4 PEOPLE TO LIFT
do this with the set screws inside the base modules.
CAUTION
E.
Connect the monitor: Fasten the short M4 screw from
the inside of the monitor through the joint profile and to
the nut on the nut plate.
LIFTINg STRAPS INCLUDED.
The lifting straps are found
in the box, together with the
monitor, ready for use.
NOTE:
The straps are not
fixed to the monitor. be
careful when lifting the
monitor so the straps do
not slide during the lifting
operation.
78-19807-02 Profile 65" Presentation Unit Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
Main system
Uppermost screw
on the bottom
module
Cable hatch
9
Connecting cables
The cables goes from one
system to the other through the
cable hatch.
NOTE:
The main system has
already been connected, only
the extra cabling needed for the
presentation unit is shown here.
10
Mounting the grilles in front and finishing up
A.
Close the top covers.
B.
Snap on the top grilles.
C.
Snap on the speaker grille.
D.
Close the base module doors.
E.
Remove the plastic foil on the
monitor frame.
F.
Use the supplied cloth to clean
up the system.
Uppermost screw
on the monitor
The nut plates are placed
inside the joint profile
Joint profile with a
slot for the cables
Presentation unit
B
Power*
From DVI-I 4 on
the C90 codec
Close the doors and snap
on the speaker grille.
Page 2
7
Level and align the systems
The nut plates are placed
In order to level the systems, use 4 pcs of the (a) set screw in the holes marked in the
inside the joint profile
picture below for each bottom module. Note that the illustration depicts a base module
as seen from above, with the door open.
Loosen nuts before adjusting the pin bolts down. When proper adjustment have been
found, tighten nuts again. These are the same nuts which were mounted in step 2 C,
see the previous page.
In step 6 the joint profile
is mounted to the main
monitor.
(In step 8 the joint profile
is mounted to the second
monitor.)
A 级声明 (A Class product declaration)
本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
Presentation unit,
(We declare here that the subject product is A class ITE product, and the
base module
following statement is clearly marked in the user manual or nameplate):
EMC Class A declaration
此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNINg:
This is a class A product. In a domestic environment this product may cause radio
WARNING:
interference in which case the user may be required to take adequate measures.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
11
Connect the power cable
Connect the presentation unit power cable. The cable is lead out from the rear side of
声明所在位置 (Position of the Declaration):
the main system.
申请号 (Application No.)：
申请人 (Applicant):
型号
(Model Number)：
* The power cable goes through
the cable hatch and to the rear side
of the main system.
B
Close the lids and
snap on the grilles.
4 × set screw (a)
Codec
Lid
警告
使用说明 User Manual
铭牌 Nameplate
签字/盖章 Signature/Stamp:
日期 Date:
Ethernet cable
PC cable
Microphone cables
Power cable
Power cable from
the Presentation unit