Cisco TelePresence Profile 65 Getting Started Manual - Page 20

Browse online or download pdf Getting Started Manual for Conference System Cisco TelePresence Profile 65. Cisco TelePresence Profile 65 46 pages. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Also for Cisco TelePresence Profile 65: User Manual (44 pages), Getting Started Manual (42 pages)

Print Page

Cisco TelePresence Video Systems

Contents

Configuring H.323 and SIP

(When not set by a provisioning system)

To get online and ready to place and receive calls, your system

must be set up properly. Your system uses either the H.323

protocol or the SIP protocol for video calls.

NOTE:

Contact your system administrator, or service provider,

for information about the network settings.

For networks administered through Cisco TMS (Cisco

TelePresence Management Suite), your Cisco TMS adminis-

trator will help you to get online.

You can find information about administering through Cisco UCM

in the

Administering TC endpoints on CUCM

Always save the new value when you change a setting

• Drop down list selection: Navigate to the correct value

and press the

( ) key to save, or press the left arrow

key

to leave without saving.

• Text entry in an input field: Enter the text, navigate to

Ok/Save

to save the change, or navigate to

to leave without saving; then press the

confirm.

Back to task overview

D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.

Introduction

User interfaces

H.323

If in doubt for any of the parameters below, contact your system

administrator or your service provider.

1. Go to

Home > Settings > Administrator settings > Advanced

configuration > H323 > Profile

2. Go to

H323Alias

corresponding input fields.

3. If you want the system to obtain the H.323 gatekeeper

address automatically, go to

in the

Discovery

guide.

address manually, select

If set to Manual, enter the gatekeeper address in the

Address

input field.

4. If the H.323 gatekeeper requires authentication, and you

want your system to authenticate itself to the gatekeeper,

go to

Authentication

list.

Enter the

ing input fields.

If authetification is not needed, select

down

list.

5. Go to

Home > Settings > System information

H.323 settings.

If you have successfully registered to the Gatekeeper, the

Status

is shown as

6. Press

Home

If you wish to change the other H.323 settings, check the admin-

istrator guide for your product.

Cancel

( ) key to

Configuration

and enter the

E164

number and

in the

Gatekeeper

and select

drop down list; if you want to enter the

Manual.

and select

in the

Mode

drop down

LoginName

and

Password

in the correspond-

Off

in the

Mode

and verify the

Registered

in the H323 section.

(

) to exit.

Appendices

SIP

If in doubt for any of the parameters below, contact your system

administrator or your service provider.

1. Go to

Home > Settings > Administrator settings > Advanced

configuration > SIP > Profile

2. Go to

URI

and enter the SIP URI in the corresponding input

field.

3. Select your preferred

DefaultTransport

Auto

down list. If you select Auto, the system first tries to connect

using Tls, then TCP, and finally UDP.

4. Select your preferred proxy

default type is Standard.

5. Go to

Proxy 1.

If you want the system to obtain the SIP

proxy address automatically, select

drop down list; if you want to enter the address manually,

select Manual.

If set to Manual, enter the proxy address in the

input field.

drop

6. If the SIP proxy requires authentication, you must enter a

Authentication 1

and enter the

in the corresponding input fields.

7. Go to

Home > Settings > System information

the SIP settings.

If you have successfully registered to a SIP server, the

Status

is shown as

Registered

8. Press

Home

(

) to exit.

If you wish to change the other SIP settings, check the admin-

istrator guide for your product.

Getting Started Guide

Contacts

protocol in the drop

Type

in the drop down list. The

Auto

in the

Discovery

Address

LoginName

and

Password

and verify

in the SIP section.