Digitool Solutions DWA-1002 User Manual - Page 2

Browse online or download pdf User Manual for Power Tool Digitool Solutions DWA-1002. Digitool Solutions DWA-1002 2 pages. Electronic torque angle wrench

Print Page

Important Safety Instructions

WARNING

Risk of flying particles.



Read this entire User's Guide before using the Torque and

Angle Wrench.



Always follow good professional tool practices.



Wear Safety goggles.



Insure that all equipment is in good working order and that

ratings of the Torque & Angle Wrench, tools and drives

exceed the torque being applied.



Never use the Torque & Angle Wrench with the power off.



Never initiate ZeroTare with torque applied.



Never use the wrench as a breaker bar to loose nuts, bolts

or fasteners.



Save these instructions.

Introduction

The DTS Torque and Angle Wrench provides Torque accuracy

within ±1% both direction CW and CCW of reading between

10% and 100% of full scale and angle accuracy ±1° of 90°

rotation @ speed 2°/s to 400°/s.

The wrench also employs a vibrator, a buzzer, and a 3-color LED.

These indicators alert users when torque or angle approaches its

preset value.

The wrench requires only two AA batteries and can operate up

200 hours of continuous use.

In addition, the DTS Torque and Angle Wrench features three

selectable torque units. They are ft-lb, in-b, and Nm.

Three modes are featured:



TORQUE - display torque value in real time, and show peak

torque when wrench is released.



ANGLE - display both maximum Angle & Torque applied for

15 seconds.

Front Panel Display and Keypad

Keypad Functions:

Power ON -

key

- Unit Select - ft-lb, in-lb or Nm

Zero Tare Torque/Angle (hold key 3 seconds)

- Mode Select TORQUE, ANGLE

- Manual power off, (hold key 3 seconds)

▲

- Increase TARGET TORQUE / ANGLE value

(Hold for rapid scrolling)

▼

- Decrease TARGET TORQUE / ANGLE value

(Hold for rapid scrolling)

Automatic Power OFF after 5 minutes of idle time.

Operator Instructions

Setup:

a. Turn on the Torque and Angle Wrench by pushing the

M buttons.

b. Press the U key

For Peak to view the units of measure.

Repeatedly push the U key to display the desired units

of measure, ft-lb, in-lb or Nm.

For Angle, pushing the U key will clear the Angle to 0°

c. Press the M key to select the display mode:

TORQUE or ANGLE Mode

d. Push the ▲ or ▼ key to view the TARGET TORQUE

or ANGLE value. Use these same keys to increase or

decrease to the desired value.

While loading in either TORQUE or ANGLE modes, the

Torque and Angle wrench will display applied torque or

angle respectively. The yellow LED and the buzzer will

begin to pulse at 80% of TARGET TORQUE, getting

faster as the TARGET TORQUE value is approached.

Application:

a. With the power on, install the Torque and Angle Wrench

insert the driver into the socket.

b. Apply torque load to the fasterner in either CW or CCW

directions.

During loading, the Torque and Angle

wrench will display applied torque in real time.

c. When the applied torque is within 4% of the TARGET

TORQUE value in TORQUE modes, the green LED,

buzzer and vibrator (optional) will output continuously.

Stop applying torque, as the installation is complete.

Release Indications:

Should the applied torque exceed the TARGET

TORQUE value by more than 4%, the red LED and

buzzer will alert continuously. If the torque over 125%

of torque range, the display will indicate "OVER

TORQUE."

Temperature Drift:

± 0.0015%/F

Storage Temperature

0ºF to 125ºF

Operating Temperature

40ºF to 110ºF

Humidity -

up to 90% non-condensing

Re-Order Components :



Torque Angle wrench



User 's Guide

P/N DWA-XXXX

P/N DTS-UG– DWA