Motorola GM640 Service Information - Page 15

Browse online or download pdf Service Information for Radio Motorola GM640. Motorola GM640 34 pages. Gm series professional radio uhf (403-470mhz)
Also for Motorola GM640: User Manual (28 pages), Service Information (32 pages), Service Information (32 pages)

Print Page

VHF (136-174MHz) Transmitter Power Amplifier (PA) 25 W

3.5

Antenna Switch

The antenna switch consists of two PIN diodes, D3471 and D3472. In the receive mode, both diodes

are off. Signals applied at the antenna jack J3401 are routed, via the harmonic ﬁlter, through

network L3472, C3474 and C3475, to the receiver input. In the transmit mode, K9V1 turns on Q3471

which enables current sink Q3472, set to 96 mA by R3473 and VR3471. This completes a DC path

from PASUPVLTG, through L3437, D3471, L3472, D3472, L3471, R3474 and the current sink, to

ground. Both diodes are forward biased into conduction. The transmitter RF from the directional

coupler is routed via D3471 to the harmonic ﬁlter and antenna jack. D3472 also conducts, shunting

RF power and preventing it from reaching the receiver port (RXIN). L3472 is selected to appear as a

lambda / 4 wave transmission line, making the short circuit presented by D3472 appear as an open

circuit at the junction of D3472 and the receiver path.

3.6

Harmonic Filter

Components L3491-L3493 and L3472, C3491-C3499 form a Chebychev low-pass ﬁlter to attenuate

harmonic energy of the transmitter to speciﬁcations level. R3491 is used to drain electrostatic

charge that might otherwise build up on the antenna. The harmonic ﬁlter also prevents high level RF

signals above the receiver passband from reaching the receiver circuits, improving spurious

response rejection.

3.7

Power Control

The transmitter uses the Power Control IC (PCIC, U3501) to control the power output of the radio. A

portion of the forward RF power from the transmitter is sampled by the directional coupler and

rectiﬁed, to provide a DC voltage to the RFIN port of the PCIC (pin 1) which is proportional to the

sampled RF power.

The ASFIC (U0221) has internal digital to analog converters (DACs) which provide a reference

voltage of the control loop to the PCIC via R3505. The reference voltage level is programmable

through the SPI line of the PCIC. This reference voltage is proportional to the desired power setting

of the transmitter, and is factory programmed at several points across the frequency range of the

transmitter to offset frequency response variations of the transmitter's power detector circuit.

The PCIC provides a DC output voltage at pin 4 (INT) which sets the drain current of the ﬁrst

(U3401) and second (Q3421) transmitter stage via current control op-amps U3402-1 and U3402-2.

This adjusts the transmitter power output to the intended value. Variations in forward transmitter

power cause the DC voltage at pin 1 to change, and the PCIC adjusts the control voltage above or

below its nominal value to raise or lower output power. Capacitors C3502-4, in conjunction with

resistors and integrators within the PCIC, control the transmitter power-rise (key-up) and power-

decay (de-key) characteristic to minimize splatter into adjacent channels. U3502 is a temperature-

sensing device, which monitors the circuit board temperature in the vicinity of the transmitter driver

and ﬁnal devices, and provides a dc voltage to the PCIC (TEMP, pin 30) proportional to temperature.

If the DC voltage produced exceeds the set threshold in the PCIC, the transmitter output power will

be reduced so as to reduce the transmitter temperature.

2-5