Philips T Series Quick Start - Page 2

Browse online or download pdf Quick Start for Monitor Philips T Series. Philips T Series 2 pages.

Print Page

Colour Monitor

Quick Start Guide

USB Cable

HDMI Cable

Silicon Foot

Stand Bar

for US

for EU

for UK

Power Plug

DC Power Adapter

(Provided by regions)

* Di erences according to regions.

Display design and accessories may di er from those illustrated above.

Wall Mount

Reset Button

Screw Hole

Volume

Stand screw

hole

VESA mount

(Screw spec: M4)

Speaker

Reserved Expansion Port

Micro USB

For SW upgrade only

Step 1

Step 2

Release the back cover

Open the back cover

screw to release back

with disassemble tool

cover

Step 5

Step 6

Install back cover thread

Route power and network cable from bottom, insert

head height not exceed

signboard before mount signboard on back cover

3mm

* Simply screw the supplied table stand onto the stand screw hole.

Landscape

Portrait

CAUTION

Rish of explosion if the battery is replaced by an incorrect type

Wait one-half hour after switching o before handling parts

Step 3

Step 4

Separate the back cover

Stick the silicon gaskets

from main device

on back cover

Step 7

* Mounting and installation

Mounting Option 1: [VESA mount]

Supporting VESA standard:

VESA MIS-D75 (75*75mm)

Supporting screw: M4*4mm

(exclude the mounting plate thickness)

Mounting Option 2: [Using back cover]

Supporting screw: Self-tapping screw *3pcs

(exclude the mounting plate thickness)

* Installation height: <2 m

CARE AND WARNING

WARNING: Changes or modi cations to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the Radio Equipment

Directive (2014/53/EU). The following test methods have been applied in order to

prove presumption of conformity with the essential requirements of the Radio

Equipment Directive This equipment is compliant with Class A of EN55032. In a

residential environment this equipment may cause radio interference.

Correct Disposal of this product. This marking indicates that this product should

not be disposed with other household wastes throughout the EU. To prevent

possible harm to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material resources. To

return your used device, please use the return and collection systems or contact the

retailer where the product was purchased. They can take this product for

environmental safe recycling.

"FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with

the FCC & CE's RF exposure guidelines, place the product at least 20cm from near by

persons. "

The suitable temperature for the Colour Monitor and sccessories is 0°C-45°C.

Adaptor with ferrite must be used with this equipment to ensure compliance with the

Class A FCC limits.

Power Adapter information:

Model No.: ADS-26SGP-12 12024E

INPUT: 100-240V~50/60Hz

OUTPUT: 12

2.0A

- Replacement of a battery with an incorrect type that can defeat a safeguard (for

example, in the case of some lithium battery types);

- Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a

battery, that can result in an explosion;

- Leaving a battery in an extremely high temperature surrounding environment that

can result in anexplosion or the leakage of ammable liquid or gas;

- A battery subjected to extremely low air pressure that may result in an explosion or

the leakage of ammable liquid or gas.