Philips Expanium AZ 1538 Manual - Page 5
Browse online or download pdf Manual for Stereo System Philips Expanium AZ 1538. Philips Expanium AZ 1538 13 pages. Cd sound system
Also for Philips Expanium AZ 1538: User Manual (2 pages), Specifications (2 pages), Service Manual (31 pages)
Print Page
POWER SUPPLY
IMPORTANT!
• Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Power
1. Check if the AC power supply, as shown on the
type plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service centre.
2. If your set is equipped with a voltage selector,
adjust the selector so that it matches with the
local mains.
3. Connect the mains lead to the wall socket.
4. To disconnect the mains supply, unplug the set
from the wall socket.
The type plate is located on the bottom of the
set.
BASIC FUNCTIONS
Switching on and off and selecting function
1. To switch on, adjust the POWER
to select: CD or TUNER function, and operate the
respective function controls.
• On and then tu or Cd are shown briefly when you
switch on to the selected function.
2. To switch off, adjust the POWER
to select POWER
OFF
Note : The DBB setting, tuner presets and the volume (up
to volume level 20) will be retained in the set's memory.
Adjusting volume and sound (See 2 )
1. Adjust the volume with the VOLUME controls.
™ Display shows the volume level UoL and a
number from 0-32.
2. Press DBB once or more to select dynamic bass
boost on or off.
/TUNER/CD
OFF
/TUNER/CD
OFF
.
DIGITAL TUNER
Tuning to radio stations
1. Adjust the POWER
™ tu is displayed briefly and then the radio
station frequency, waveband and, if
programmed, a preset number are shown.
(See 3 )
2. Press CD MODE/BAND once or more to select
your waveband.
3. Press and hold SEARCH ∞ or § until the
frequency in the display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows Srch
during automatic tuning.
4. Repeat step 3 if necessary until you find the
desired station.
To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal reception.
To improve radio reception:-
• For FM, extend, incline and turn the telescopic
aerial. Reduce its length if the signal is too strong.
• For MW (AM)/LW, the set uses a built-in aerial.
Direct this aerial by turning the whole set.
Programming radio stations
You can store up to a total of 40 radio stations in the
memory, manually or automatically (Autostore).
Manual programming
1. Tune to your desired station (see Tuning to radio
stations).
2. Press PROG to activate programming.
™ Display: Pr -- and
3. Use the digit panel on the set to key in a number,
1-40, to select a preset station. E.g. press 1,1 if you
want to store your station as preset 11.(See 4 )
Note : If a higher preset number, 41-49 is selected, the
display will show noPr and tune to Pr 4. Presets
exceeding 50, e.g. 67 will tune you to presets 6 and 7.
• Remote control: Press PRESET
more to select a preset station.
• Set: press ALBUM (
4. Press PROG to confirm.
5. Repeat steps 1-4 to store other stations.
Note : You can erase a preset station by storing
another frequency in its place.
DIGITAL TUNER
/TUNER/CD to TUNER.
OFF
flashes.
PROGRAM
-
+
/
once or
-
+
/
)