Pioneer DEH P4800MP Operation Manual - Page 29

Browse online or download pdf Operation Manual for Car Receiver Pioneer DEH P4800MP. Pioneer DEH P4800MP 36 pages. Multi-cd control high power cd/mp3/wma player with rds tuner

Print Page

MAN-DEH-P4800MP-GB.fm Page 29 Thursday, September 29, 2005 11:55 AM

Initial Settings

Switching Auto PI Seek

The unit can automatically search for a different station with the same programming,

even during preset recall.

1. Press FUNCTION to select A-PI.

Press FUNCTION repeatedly until A-PI appears in the display.

2. Press 8 or 2 to turn A-PI on or off.

Pressing 8 or 2 will turn A-PI on or off and that status will be displayed (e.g., A-PI

:ON).

Switching the auxiliary setting

Auxiliary equipments connected to this unit can be activated individually. Set each

AUX source to ON when using. About connecting or using auxiliary equipments, refer

to "Using the AUX source" on page 30.

1. Press FUNCTION to select AUX1/AUX2.

Press FUNCTION repeatedly until AUX1/AUX2 appears in the display.

2. Press 8 or 2 to turn AUX1/AUX2 on or off.

Pressing 8 or 2 will turn AUX on or off and that status will be displayed (e.g., AUX1

:ON).

Setting the rear output and subwoofer controller

This unit's rear output (rear speaker leads output and RCA rear output) can be used

for full-range speaker (R-SP :FUL) or subwoofer (R-SP :S/W) connection. If you

switch the rear output setting to R-SP :S/W, you can connect a rear speaker lead

directly to a subwoofer without using an auxiliary amp.

Initially, the unit is set for rear full-range speaker connection (R-SP :FUL). When rear

output is connected to full range speakers (when R-SP :FUL is selected), you can

connect other full range speakers (P/O :FUL) or a subwoofer (P/O :S/W) to the RCA

rear output.

1. Press FUNCTION to select R-SP.

Press FUNCTION repeatedly until R-SP appears in the display.

2. Press 8 or 2 to switch the rear output setting.

Pressing 8 or 2 will switch between R-SP :FUL (full-range speaker) and R-SP :S/W

(subwoofer) and that status will be displayed.

• When no subwoofer is connected to the rear output, select R-SP :FUL.

• When a subwoofer is connected to the rear output, set for subwoofer R-SP :S/W.

• When the rear output setting is R-SP :S/W, you cannot operate the following

procedure.

3. Press 4 or 6 to switch the subwoofer output or rear output.

Pressing 4 or 6 will switch between P/O :S/W and P/O :FUL and that status will be

displayed.

Notes

• Even if you change this setting, there is no output unless you turn the subwoofer output on

(refer to "Using subwoofer output" on page 26).

• If you change this setting, subwoofer output in the audio menu return to the factory settings.

Saving the battery consumption

Even when this unit is switched off, the microcomputer inside still uses a small amount

of power in order to enable a quick restart. Switching on the Power Save mode will

prevent the microcomputer from running unnecessarily, thereby saving the battery in

your vehicle.

• With Power Save mode on, you cannot insert or eject a disc when power to the unit

is off. Press SOURCE to switch the unit on, then try again.

Important

If the battery in your vehicle is disconnected the Power Save mode is canceled. Turn

on Power Save again once the battery has been reconnected. If the ignition switch in

your vehicle doesn't have an ACC (accessory) position, it is possible depending on the

connection method that when Power Save is off, the unit will draw power from the

battery.

1. Press FUNCTION to select SAVE.

2. Press 8 or 2 to turn power save on or off.