Pioneer DEH-4400BT Operation Manual - Page 19

Browse online or download pdf Operation Manual for Car Receiver Pioneer DEH-4400BT. Pioneer DEH-4400BT 30 pages. Cd rds receiver
Also for Pioneer DEH-4400BT: Installation Manual (33 pages), Quick Start Manual (8 pages)

Print Page

Section

Operating this unit

Initial settings

Important

PW SAVE (power saving) is cancelled if the vehi-

cle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depending

on connection methods, the unit may continue to

draw power from the battery if your vehicle's igni-

tion doesn't have an ACC (accessory) position.

Press and hold SRC/OFF until the unit

turns off.

Press SRC/OFF and hold until function

name appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock dis-

play you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

CLOCK (clock display)

You can turn the clock display on or off.

The clock display disappears temporarily when you

perform other operations, but the clock display ap-

pears again after 25 seconds.

1 Press M.C. to turn the clock display on or off.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek tun-

ing is 50 kHz. When AF or TA is on, the tuning step

automatically changes to 100 kHz. It may be prefer-

able to set the tuning step to 50 kHz when AF is on.

! The tuning step remains at 50 kHz during manual

tuning.

1 Press M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

AUTO-PI (auto PI seek)

The unit can automatically search for a different sta-

tion with the same programming, even during preset

recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary device

connected to this unit.

1 Press M.C. to turn AUX on or off.

USB PNP (plug and play)

This setting allows you to switch your source to USB/

iPod automatically.

1 Press M.C. to turn the plug and play function on

or off.

ON – When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit's source

is turned off.

OFF – When a USB storage device/iPod is con-

nected, the source is not switched to USB/iPod

automatically. Please change the source to USB/

iPod manually.

REAR-SP (rear output setting)

The rear speaker leads output can be used for full-

range speaker or subwoofer connection.

If you switch to SW, you can connect a rear speaker

lead directly to a subwoofer without using an auxiliary

amp.

Initially, REAR-SP is set for rear full-range speaker

connection (FUL).

1 Press M.C. to select the desired setting.

FUL—SW

! Even if you change this setting, there will be

! If you change this setting, subwoofer output

PREOUT (preout setting)

The RCA outputs can be used for rear speaker or sub-

woofer connection.

If you switch to SW, you can connect a rear speaker

lead directly to a subwoofer without using an auxiliary

amp.

Initially, PREOUT is set for rear full-range speaker con-

nection (SW).

1 Press M.C. to select the desired setting.

SW—REA

! Even if you change this setting, there will be

! If you change this setting, subwoofer output

DEMO (demo display setting)

Autogood products «130»

no output if you select OFF in SUB.W (Refer to

SUB.W (subwoofer on/off setting) on the pre-

vious page).

in the audio menu will return to the factory

settings.

no output if you select OFF in SUB.W (Refer to

SUB.W (subwoofer on/off setting) on the pre-

vious page).

in the audio menu will return to the factory

settings.