Pioneer DEH-9300SD Operation Manual - Page 14

Browse online or download pdf Operation Manual for Car Receiver Pioneer DEH-9300SD. Pioneer DEH-9300SD 28 pages. Cd rds receiver
Also for Pioneer DEH-9300SD: Quick Start Manual (17 pages)

Print Page

Section

Operating this unit

Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

Fader/Balance (fader/balance adjustment)

1 Push M.C. up or down to adjust the front/rear

speaker balance.

! The front/rear speaker balance cannot be ad-

justed when the rear output setting is Rear

SP :S/W. Refer to S/W control (rear output

and subwoofer setting) on page 16.

2 Push M.C. left or right to adjust the left/right

speaker balance.

Powerful (equalizer recall)

1 Push M.C. left or right to select an equalizer

curve.

Powerful—Natural—Vocal—Custom1—Cus-

tom2—Flat—Super bass

100 Hz (equalizer adjustment)

You can adjust the currently selected equalizer curve

setting as desired. Adjusted equalizer curve settings

are stored in Custom1 or Custom2.

! A separate Custom1 curve can be created for

each source. If you make adjustments when a

curve other than Custom2 is selected, the equali-

zer curve settings will be stored in Custom1.

! A Custom2 curve that is common for all sources

can be created. If you make adjustments when

the Custom2 curve is selected, the Custom2

curve will be updated.

1 Recall the equalizer curve you want to adjust.

2 Push M.C. left or right to select the equalizer

band to adjust.

100Hz—315Hz—1.25kHz—3.15kHz—8kHz

3 Push M.C. up or down to adjust the equalizer

curve.

+6 to –6 is displayed as the equalizer curve is in-

creased or decreased.

LOUD (loudness)

Loudness compensates for deficiencies in the low-

and high-frequency ranges at low volume.

1 Press M.C. to turn loudness on or off.

2 Push M.C. left or right to select the desired set-

ting.

Low (low)—Mid (mid)—High (high)

Sub W.1 (subwoofer on/off setting)

This unit is equipped with a subwoofer output which

can be turned on or off.

1 Press M.C. to turn subwoofer output on or off.

2 Push M.C. left or right to select the phase of sub-

woofer output.

Push M.C. left to select reverse phase and Re-

verse appears in the display. Push M.C. right to

select normal phase and Normal appears in the

display.

Sub W.2 (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Push M.C. left or right to select the cut-off fre-

quency.

50Hz—63Hz—80Hz—100Hz—125Hz

2 Push M.C. up or down to adjust the output level

of the subwoofer.

Each time M.C. is pushed up or down, subwoofer

level increases or decreases. +6 to -24 is dis-

played as the level is increased or decreased.

Bass (bass boost)

1 Push M.C. up or down to select a desired level.

0 to +6 is displayed as the level is increased or de-

creased.

HPF (high pass filter adjustment)

When you do not want low sounds from the subwoo-

fer output frequency range to play from the front or

rear speakers, turn on the HPF (high pass filter). Only

frequencies higher than those in the selected range

are output from the front or rear speakers.

1 Press M.C. to turn high pass filter on or off.

2 Push M.C. left or right to select the cut-off fre-

quency.

50Hz—63Hz—80Hz—100Hz—125Hz

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! When selecting FM as the source, you cannot

switch to SLA.

! Settings are based on the FM volume level, which

remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

1 Push M.C. up or down to adjust the source vo-

lume.

Adjustment range: +4 to –4