Pioneer DEH-P4300RB Installation Manual - Page 3
Browse online or download pdf Installation Manual for Car Receiver Pioneer DEH-P4300RB. Pioneer DEH-P4300RB 6 pages. Multi-cd control high power cassette player with rds tuner
Print Page
Connecting the Units
8.
Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
1*
3*
2*
2. Rear or Subwoofer output
3. Antenna jack
5*
4*
9. Connect leads of the same
4. IP-BUS cable
color to each other.
10. Cap (1*)
5. IP-BUS input (Blue)
When not using this terminal,
do not remove the cap.
6. Multi-CD player
(sold separately)
11. Yellow (3*)
12. Yellow (2*)
Back-up
To terminal always supplied
(or accessory)
with power regardless of
ignition switch position.
13. Red (5*)
14. Red (4*)
Accessory
To electric terminal controlled
(or back-up)
by ignition switch (12 V DC)
ON/OFF.
15. Orange/white
To lighting switch terminal.
16. Black (ground)
To vehicle (metal) body.
17. ISO connector
Note:
18. Yellow/black
In some vehicles, the ISO connector may be
If you use a cellular telephone, connect it via the
divided into two. In this case, be sure to
Audio Mute lead on the cellular telephone. If not,
connect to both connectors.
keep the Audio Mute lead free of any connections.
20. Connecting cords with RCA pin plugs
(sold separately)
1. This Product
7. Fuse
22. Blue/white
To system control terminal of
the power amp (max. 300 mA
12 V DC).
23. System remote control
24. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
25. Blue/white (6*)
26. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
27. Left
28. Right
29. Rear Speaker
29. Rear Speaker
or Subwoofer
30. Perform these connections when using
a different amp (sold separately).
19. Speaker leads
: Front left +
White
31.
Note:
: Front left ≠
White/black
When a subwoofer is connected to this unit
: Front right +
Gray
instead of a rear speaker, change the rear
Gray/black
: Front right ≠
output setting in the Initial Setting. (Refer to
: Rear left + or Subwoofer +
Green
the Operation Manual.)
: Rear left ≠ or Subwoofer ≠
Green/black
The subwoofer output of this unit is
: Rear right + or Subwoofer +
Violet
monaural.
: Rear right ≠ or Subwoofer ≠
Violet/black
Connecting the Units
Note:
•
This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
•
To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin-
ning installation.
21. Power amp
•
Refer to the owner's manual for details on con-
(sold separately)
necting the power amp and other units, then
make connections correctly.
•
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
•
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
•
Don't pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
•
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
•
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
•
When replacing fuse, be sure to use only fuse of
the rating prescribed on this product.
or Subwoofer
•
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right ≠ speaker leads are com-
mon.
•
Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.
Fig. 5
Abb. 5
Afb. 5
Connection Diagram (Fig. 5)
•
When this product's source is switched ON, a
control signal is output through the blue/white
1. This product
lead. Connect to an external power amp's system
2. Rear or Subwoofer output
remote control or the car's Auto-antenna relay
3. Antenna jack
control terminal (max. 300 mA 12 V DC). If the
4. IP-BUS cable
car features a glass antenna, connect to the anten-
5. IP-BUS input (Blue)
na booster power supply terminal.
6. Multi-CD player (sold separately)
•
When an external power amp is being used with
7. Fuse
this system, be sure not to connect the blue/white
8. Note:
lead to the amp's power terminal. Likewise, do
Depending on the kind of vehicle, the function of
not connect the blue/white lead to the power ter-
3* and 5* may be different. In this case, be sure
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
to connect 2* to 5* and 4* to 3*.
•
To avoid short-circuiting, cover the disconnected
9. Connect leads of the same color to each other.
lead with insulating tape. Especially, insulate the
10. Cap (1*)
unused speaker leads without fail. There is a pos-
When not using this terminal, do not remove the
sibility of short-circuiting if the leads are not
cap.
insulated.
11. Yellow (3*)
•
To prevent incorrect connection, the input side of
Back-up (or accessory)
the IP-BUS connector is blue, and the output side
12. Yellow (2*)
is black. Connect the connectors of the same col-
To terminal always supplied with power regard-
ors correctly.
less of ignition switch position.
•
If this unit is installed in a vehicle that does not
13. Red (5*)
have an ACC (accessory) position on the ignition
Accessory (or back-up)
switch, the red lead of the unit should be con-
14. Red (4*)
nected to a terminal coupled with ignition switch
To electric terminal controlled by ignition switch
ON/OFF operations. If this is not done, the vehi-
(12 V DC) ON/OFF.
cle battery may be drained when you are away
15. Orange/white
from the vehicle for several hours.
To lighting switch terminal.
16. Black (ground)
To vehicle (metal) body.
17. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
18. Yellow/black
If you use a cellular telephone, connect it via the
ACC position
No ACC position
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connec-
•
The black lead is ground. Please ground this lead
tions.
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
•
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.
<ENGLISH>
19. Speaker leads
: Front left +
White
White/black : Front left ≠
Gray
: Front right +
Gray/black : Front right ≠
: Rear left + or Subwoofer +
Green
Green/black : Rear left ≠ or Subwoofer ≠
: Rear right + or Subwoofer +
Violet
Violet/black : Rear right ≠ or Subwoofer ≠
20. Connecting cords with RCA pin plugs (sold
separately)
21. Power amp (sold separately)
22. Blue/white
To system control terminal of the power amp
(max. 300 mA 12 V DC).
23. System remote control
24. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
25. Blue/white (6*)
26.The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
27. Left
28. Right
29. Rear Speaker or Subwoofer
30. Perform these connections when using a different
amp (sold separately).
31. Note:
When a subwoofer is connected to this unit
instead of a rear speaker, change the rear output
setting in the Initial Setting. (Refer to the
Operation Manual.)
The subwoofer output of this unit is monaural.