Pioneer Super Tuner IIID DEH-P6200BT Installation Manual - Page 5

Browse online or download pdf Installation Manual for Car Receiver Pioneer Super Tuner IIID DEH-P6200BT. Pioneer Super Tuner IIID DEH-P6200BT 8 pages. Cd receiver
Also for Pioneer Super Tuner IIID DEH-P6200BT: Operation Manual (49 pages)

Print Page

Installation

English

DIN Front-mount

Note

1. Insert the mounting sleeve into the

• Check all connections and systems before final

installation.

dashboard.

• Do not use unauthorized parts. The use of

• When installing in a shallow space, use a

unauthorized parts may cause malfunctions.

supplied mounting sleeve. If there is enough

• Consult with your dealer if installation requires

space behind the unit, use factory supplied

drilling of holes or other modifications of the

mounting sleeve.

vehicle.

• Do not install this unit where:

2. Secure the mounting sleeve by

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result of

using a screwdriver to bend the

a sudden stop.

metal tabs (90°) into place.

• The semiconductor laser will be damaged if it

overheats. Install this unit away from hot places

Mounting sleeve

Dashboard

such as near the heater outlet.

• Optimum performance is obtained when the unit

182

is installed at an angle of less than 60°.

60°

3. Install the unit as illustrated.

• Use commercially available parts when

installing.

• When installing, to ensure proper heat dispersal

when using this unit, make sure you leave ample

Nut

space behind the rear panel and wrap any loose

Firewall or

cables so they are not blocking the vents.

metal support

Dashboard

Leave ample space

Metal strap

Screw

10 cm

Screw (M4 8)

10 cm

DIN Front/Rear-mount

• Make sure that the unit is installed securely

in place. Unstable installation may cause this

This unit can be properly installed either from

unit to malfunction, such as sound skip.

"Front" (conventional DIN Front-mount) or

DIN Rear-mount

"Rear" (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit

1. Determine the appropriate position

chassis). For details, refer to the following

where the holes on the bracket and

installation methods.

the side of the unit match.

Installation

English

3. Pull the unit out of the dashboard.

2. Tighten two screws on each side.

Screw

Fastening the front panel

If you do not plan to detach the front panel,

the front panel can be fastened with supplied

Dashboard or Console

screw.

Factory radio mounting bracket

• Use either truss (5 mm × 8 mm) or flush

surface (5 mm × 9 mm) screws, depending

on the bracket screw holes.

Screw

Removing the Unit

1. Extend top and bottom of the trim

ring outwards to remove the trim

ring. (When reattaching the trim

ring, point the side with the groove

down.)

Trim ring

• Releasing the front panel allows easier access

to the trim ring.

2. Insert the supplied extraction keys

into both sides of the unit until

they click into place.

Installation

English

Installing the microphone

2. Install the microphone clip on the

sun visor.

Installation notes

• With the sun visor up, install the microphone

Install the microphone in a position and

clip. (Lowering the sun visor reduces the voice

recognition rate.)

orientation that will enable it to pick up the

voice of the person operating the system.

Microphone clip

CAUTION

• It is extremely dangerous to allow the microphone

lead to become wound around the steering

column or gearstick. Be sure to install the unit in

such a way that it will not obstruct driving.

When installing the microphone

on the sun visor

1. Install the microphone on the

microphone clip.

Clamp

Use separately sold

clamps to secure the

lead where necessary

Microphone

inside the vehicle.

When installing the microphone

Microphone clip

on the steering column

1. Install the microphone on the

microphone clip.

Microphone

Microphone base

Fit the

Microphone clip

microphone lead

into the groove.

• Microphone can be installed without using

microphone clip. In this case, detach the

microphone base from the microphone

clip. To detach the microphone base from

microphone clip, slide the microphone base.

Installation

English

2. Install the microphone clip on the

steering column.

Double-sided tape

Install the microphone clip on the

rear side of the steering column.

Clamp

Use separately sold

clamps to secure

the lead where

necessary inside the

vehicle.

Adjusting the microphone

angle

The microphone angle can be adjusted.