Pioneer X-EM22 Operating Instructions Manual - Page 15

Browse online or download pdf Operating Instructions Manual for Car Receiver Pioneer X-EM22. Pioneer X-EM22 28 pages. Cd receiver system

Print Page

Pioneer X-EM22 Operating Instructions Manual

Bluetooth® Audio playback (X-EM22 only)

Confirm on the Bluetooth capable device

that pairing has been completed.

• If pairing with the Bluetooth capable device has been

completed correctly, a beep will sound, and the

Bluetooth indicator will switch from blinking to staying

lit.

• If the Bluetooth indicator will not switch from blinking to

staying lit, the pairing was not completed correctly so

please try pairing with the unit again.

• If paring has been completed correctly, you need not

repeat this procedure again.

Even devices that have already been paired with this unit will

not connect during pairing mode in the following cases.

In such cases, delete pairing history from the Bluetooth

wireless technology device and perform pairing again.

In order to pair with the unit, press and hold the  on the

unit for 3 seconds.

• Up to 8 pairing history can be recorded with this unit. If

connecting to a Bluetooth wireless technology device

over 8 units, the oldest pairing history will be deleted.

• If the settings are reset to the factory setting, all pairing

history will be deleted. In order to reset to factory setting,

press and hold the  on the unit for more than 8

seconds.

Listen to music on the unit from a

Bluetooth capable device

Press BLUETOOTH on the remote control or

INPUT repeatedly on the main unit to switch the

source to [BT].

The unit will start using the BT function, and connect with a

Bluetooth capable device.

A Bluetooth connection will be created

between the Bluetooth capable device and the

unit.

Procedures for connecting to the unit should be performed

from the Bluetooth capable device.

• Please refer to the user's manual for your Bluetooth

capable device for details of the connection procedures.

Playback music from the Bluetooth capable

device.

Note

• When Bluetooth capable devise is not connected and no

operations have been performed for more than 15

minutes, the unit will automatically power off.

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is a

band used by other wireless systems (see list below). To

prevent noise or interrupted communication, do not use this

unit nearby such devices, or make sure these devices are

switched off during use.

• Cordless phones

• Cordless facsimiles

• Microwave ovens

• Wireless LAN devices (IEEE802.11b/g)

• Wireless AV equipment

• Wireless controllers for game systems

• Microwave-based health aids

• Some baby monitors

Other, less common, equipment that may operate on the

same frequency:

• Anti-theft systems

• Amateur radio stations (HAM)

• Warehouse logistic management systems

• Discrimination systems for train or emergency vehicles

Note

• In the event noise appears in your television image, there

is the possibility that a Bluetooth wireless technology

enabled device or this unit (including products

supported by this unit) are causing signal interference

with the antenna input connector of your television,

video, satellite tuner, etc. In this event, increase the

distance between the antenna input connector and the

Bluetooth wireless technology enabled device or this

unit (including products supported by this unit).

• If there is something obstructing the path between this

unit (including devices supported by this unit) and the

device equipped with Bluetooth wireless technology

(such as a metal door, concrete wall, or insulation

containing tinfoil), you may need to change the location

of your system to prevent signal noise and interruptions.

Scope of operation

Use of this unit is limited to home use. (Transmission

distances may be reduced depending on communication

environment).

In the following locations, poor condition or inability to receive

radio waves may cause the audio to be interrupted or stopped:

• In reinforced concrete buildings or steel framed or iron-

framed buildings.

• Near large metallic furniture.

• In a crowd of people or near a building or obstacle.

• In a location exposed to the magnetic field, static

electricity or radio wave interference from radio

communication equipment using the same frequency

band (2.4 GHz) as this unit, such as a 2.4 GHz wireless

LAN device (IEEE802.11b/g) or microwave oven.