Pioneer XDV-P6 - DVD Changer - in-dash Installation Manual - Page 4

Browse online or download pdf Installation Manual for Car Receiver Pioneer XDV-P6 - DVD Changer - in-dash. Pioneer XDV-P6 - DVD Changer - in-dash 9 pages. Other manual
Also for Pioneer XDV-P6 - DVD Changer - in-dash: Installation Manual (5 pages)

Print Page

Installation

Note:

• If the hide-away unit is installed under a front seat,

• Before making a final installation of the unit, tem-

make sure it does not obstruct seat movement.

Route all leads and cords carefully around the slid-

porarily connect the wiring to confirm that the

ing mechanism so they do not get caught or

connections are correct and the system works

properly.

pinched in the mechanism and cause a short cir-

• Use only the parts included with the unit to ensure

cuit.

proper installation. The use of unauthorized parts

can cause malfunctions.

MODE Switch Setting

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

Before installing, use a pen tip or other thin,

tions of the vehicle.

pointed instrument to set the MODE Switch to

• Install the unit where it does not get in the driver's

the appropriate position for the component you

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

are using it with.

• Do not place the display (sold separately) in a

position where it will impede the driver's visibility

IP BUS

STAND ALONE

or affect the operation of your vehicle's air bags.

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

Installing the hide-away unit

the unit might not give its optimum performance.

Mounting with Velcro Tape

Thoroughly wipe off the surface before

affixing the velcro tape.

Hide-away unit

Velcro tape

(large) (hard)

• When mounting the hide-away unit, make sure

Velcro tape

none of the leads are trapped between the hide-

(large) (soft)

away unit and the surrounding metalwork or fit-

tings.

• Do not mount the hide-away unit near the heater

outlet, where it would be affected by heat, or near

the doors, where rainwater might splash onto it.

Car mat or chassis

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not

drill into the gas line, brake line, electrical wiring

or other important parts.

• If the hide-away unit is installed in the passenger

compartment, anchor it securely so it does not

break free while the car is moving, and cause

injury or an accident.

DIN Front/Rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush

Holder

After inserting the holder into the dash-

board, then select the appropriate tabs

according to the thickness of the dash-

Dashboard

board material and bend them.

(Install as firmly as possible using the

1 1 82

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Rubber bush

Screw

Frame

Removing the unit

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it.

(When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

Insert the supplied extraction keys into the

unit, as shown in the figure, until they

click into place. Keeping the keys pressed

against the sides of the unit, pull the unit

out.

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame.

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it.

(When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

2. Fastening the unit to the factory radio mounting bracket.

Select a position where the screw holes of the

bracket and the screw holes of the head unit

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either

truss screws (5 × 8 mm) or flush surface

screws (5 × 8 mm), depending on the shape of

the screw holes in the bracket.

Screw

Dashboard or Console

Factory radio mounting

bracket

Mounting with Brackets

Tapping screw (6 × 16 mm)

Cover

Bracket

Truss screw (5 × 8 mm)

Car mat or chassis

Drill 4 to 4.5 mm (1/8 in.) diameter holes.