Pioneer DEH-P5100UB - Radio / CD Installation Manual

Browse online or download pdf Installation Manual for Receiver Pioneer DEH-P5100UB - Radio / CD. Pioneer DEH-P5100UB - Radio / CD 6 pages. Cd rds receiver
Also for Pioneer DEH-P5100UB - Radio / CD: Brochure (9 pages), Installation Manual (8 pages), Quick Start Manual (8 pages)

Print Page

Pioneer DEH-P5100UB - Radio / CD Installation Manual

CD RECEIVER

AUTORADIO CD

RADIO CD

DEH-P5100UB

Installation Manual

Manuel d'installation

Manual de instalación

Printed in Thailand

Imprimé en Thaïlande

QRD3031-A/N

> UC

Installation

English

2. Secure the mounting sleeve by

Note

using a screwdriver to bend the

• Check all connections and systems before final

metal tabs (90°) into place.

installation.

Mounting sleeve

• Do not use unauthorized parts. The use of

Dashboard

unauthorized parts may cause malfunctions.

• Consult with your dealer if installation requires

182

drilling of holes or other modifications of the

vehicle.

• Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

• The semiconductor laser will be damaged if it

3. Install the unit.

overheats. Install this unit away from hot places

• Use commercially available parts when

such as near the heater outlet.

installing.

• Optimum performance is obtained when the unit

Nut

is installed at an angle of less than 60°.

Firewall or

metal support

60°

Metal strap

Screw

DIN Front/Rear-mount

Screw (M4 8)

This unit can be properly installed either from

"Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit

chassis). For details, refer to the following

installation methods.

• Make sure that the unit is installed securely

in place. Unstable installation may cause this

DIN Front-mount

unit to malfunction, such as sound skip.

Removing the Unit

Installation with metal strap and

1. Extend top and bottom of the trim

screws

ring outwards to remove the trim

1. Insert the mounting sleeve into the

ring. When reattaching the trim

dashboard.

ring, push the trim ring onto the

• When installing in a shallow space, use a

unit until it clicks. (If the trim ring is

supplied mounting sleeve. If there is enough

attached upside down, the trim ring

space behind the unit, use factory supplied

mounting sleeve.

will not fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

Trim ring

Installation

English

2. Insert the supplied extraction keys

3. Tighten two screws on each side.

• Use either truss screws (5 mm × 8 mm)

into both sides of the unit until

or flush surface screws (5 mm × 9 mm),

they click into place.

depending on the shape of screw holes in the

bracket.

Screw

Dashboard or Console

Factory radio mounting bracket

3. Pull the unit out of the dashboard.

Fastening the front panel

DIN Rear-mount

If you do not plan to detach the front panel,

1. Extend top and bottom of the trim

the front panel can be fastened with supplied

ring outwards to remove the trim

screw.

ring. When reattaching the trim ring,

push the trim ring onto the unit until

it clicks. (If the trim ring is attached

upside down, the trim ring will not

fit properly.)

Screw

• It becomes easy to remove the trim ring if the

front panel is released.

Trim ring

2. Determine the appropriate position

where the holes on the bracket and

the side of the unit match.

Connecting the unit

English

• Control signal is output through blue/white cable

Note

when this unit is powered on. Connect it to an

external power amp's system remote control or

• When this unit is installed in a vehicle without

the vehicle's auto-antenna relay control terminal

ACC (accessory) position on the ignition switch,

(max. 300 mA, 12 V DC). If the vehicle is equipped

red cable must be wired to the terminal that

with a glass antenna, connect it to the antenna

can detect the operation of the ignition key.

booster power supply terminal.

Otherwise, battery drain may result.

• Never connect blue/white cable to external

power amp's power terminal. Also, never connect

it to the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• Black cable is ground. This cable and other

product's ground cable (especially, high-current

products such as power amp) must be wired

ACC position

No ACC position

separately. Otherwise, fire or malfunction may

result if they are accidentally detached.

• Use this unit in other than the following

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's

negative cables.