Pioneer GM-6000F Owner's Manual - Page 4

Browse online or download pdf Owner's Manual for Amplifier Pioneer GM-6000F. Pioneer GM-6000F 9 pages. Bridgeable four-channel power amplifier
Also for Pioneer GM-6000F: Owner's Manual (6 pages)

Print Page

1. Connecting the Speakers and Input Wires

Installation

Example of installation on the floor

CAUTION

mat or on the chassis

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

1. Place the amplifier where it is to be

—Places where it may interfere with the driver,

installed. Insert the supplied tapping

such as on the floor in front of the driver's

× 18 mm) into the screw

screws (4

seat.

• Make sure that wires are not caught in the sliding

holes. Push on the screws with a

mechanism of the seats, resulting in a short-cir-

screwdriver so they make marks

cuit.

where the installation holes are to be

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

located.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

2. Drill 2.5 mm (1/8 inch) diameter

from damage.

holes at the point marked, and

• Install tapping screws in such a way that the

install the amplifier, either on the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

carpet or directly to the chassis.

of the car, which can result in fire.

• To prevent electric shock, do not install the ampli-

Tapping-screws

fier in places where it might come in contact with

(4 × 18 mm)

liquids.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

Drill a 2.5 mm (1/8 inch)

—Allow adequate space above the amplifier for

diameter hole

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• Do not install the amplifier near a door where it

may get wet.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Specifications

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 27.1 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 9.1 A (4 Ω for four channels)

Fuse .......................................................................................................................................................................... 20 A × 2

Dimensions ........................................................................................................................ 300 (W) × 61 (H) × 324 (D) mm

Weight ...................................................................................................... 5.2 kg (12.0 lbs) (Leads for wiring not included)

Maximum power output .................................................................................................................... 100 W × 4 / 240 W × 2

Continuous power output .......................................................... 50 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD)

120 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)

60 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

Frequency response ............................................................................................................ 10 — 50,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ........................................................................................................................ 95 dB (IHF–A network)

Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 65 dB (1 kHz)

Low pass filter .................................................................................................................... Cut off frequency: 40 — 120 Hz

High pass filter .................................................................................................................. Cut off frequency: 40 — 120 Hz

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.4 — 6.5 V)

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

Floor mat

drawn by multiple power amplifiers.

or chassis

14.5 A (4 Ω for two channels)

[12 (W) × 2-3/8 (H) × 12-3/4 (D) in]

(Bridge connection: 4 — 8 Ω allowable)

Cut off slope: –12 dB/oct