Pioneer SCU-M2096ZH Service Manual - Page 44
Browse online or download pdf Service Manual for Amplifier Pioneer SCU-M2096ZH. Pioneer SCU-M2096ZH 46 pages. Multi-cd control rds tuner amplifier
SCU-M2096ZH,CD-R1546ZH
ADJUSTING VOLUME ....... [12]
The volume is increased by pressing
5
the (
) side of button [12], and
decreased by pressing the (
(Display shows "VOL 00"~"VOL 30".)
• Do not turn up the volume
level so loud that you cannot
hear emergency vehicles or
traffic.
• Listening to the sound
through headset for a long
period of time with the
maximum volume level may
cause hearing damage.
Advice
• Use this audio system at a volume
level that does not annoy other
people.
Adjusting the Fader
This function lets you adjust the
balance between rider speaker/headset
and passenger headset volume levels.
Select the fader adjustment mode. If
5
you press the (
) side of button [12]
the balance gradually changes until
sound is output from the rider
speaker/headset only. If you press the
∞
(
) side of button [12] the balance
gradually changes until sound is
output from the passenger headset
only. (Display shows "FAD F9"~
"FAD R9".)
Advice
• When not using the passenger
headset, the setting should be
"FAD F9"~"FAD 0".
44
ADJUSTING
AUDIO ................... [4]
Press button [4] to switch to the mode
in which you want to make the
∞
) side.
adjustment, and make the adjustment
using button [12]. The adjustment
mode changes each time button [4] is
pressed, as shown below.
No-indication (Volume Adjustment)
BAS (Bass Adjustment)
TRE (Treble Adjustment)
BAL (Balance Adjustment)
FAD (Fader Adjustment)
Advice
• When bass, treble, balance and
fader adjustments are made, a
beep will be heard at the center
position. The adjustment mode is
canceled approximately 5 seconds
after an adjustment is made.
USING THE RADIO
[ 1 ]
[ 3 ]
[ 11 ]
• Keep both hands on the
handlebars while riding.
Adjusting Bass
[12]
Select the bass adjustment mode.
Bass intensity is gradually increased
by pressing the (
and decreased by pressing the (
side. (Display shows "BAS –6"~
"BAS 6".)
Adjusting Treble
Select the treble adjustment mode.
Treble intensity is gradually increased
by pressing the (
and decreased by pressing the (
side. (Display shows "TRE –6"~
"TRE 6".)
Adjusting Balance
Select the balance adjustment mode.
The balance is gradually changed to
left speaker sound only, by pressing
the (
speaker sound only, by pressing the
(
"BAL R9".)
LISTENING TO
THE RADIO ............... [1]
[ 5 ]
[ 6 ] [ 7 ] [ 8 ]
[ 9 ]
When button [1] is pressed, the radio
power is turned on and the Band )
and Frequency ( are displayed. To
NEWS
TP
ST
turn the radio off, press button [9].
AF
REG
RPT
TA
A.SEL
CH
CHANGING THE BAND ....... [1]
The band is selected by pressing
button [1] repeatedly. Each time the
button is pressed, the band changes in
[ 10 ]
the following order.
U1 (FM1) t U2(FM2) t UT(FMT) t M/L(MW/LW)
5
) side of button [12],
5
) side of button [12],
∞
) side of button [12], and to right
5
) side. (Display shows "BAL L9"~
Advice
• During MW/LW reception, engine
noise may drown out the broadcast
so that you cannot hear it.
∞
)
∞
)
[9]