Pioneer CDJ-1000MKII Operating Instructions Manual - Page 18

Browse online or download pdf Operating Instructions Manual for CD Player Pioneer CDJ-1000MKII. Pioneer CDJ-1000MKII 20 pages. Compact disc player

Print Page

Pioneer CDJ-1000MKII Operating Instructions Manual

OTHERS

TROUBLESHOOTING

Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart below. Sometimes incorrect operation may be due to a

malfunction in another component. If the problem is not fixed, check the other components used with the player. If the problem still persists, contact your nearest Pioneer

authorized service center or dealer for service.

Symptom

Disc doesn't eject even when EJECT button (0) is

pressed.

Play doesn't commence even when the disc is in-

serted.

Playback immediately stops when started. During

playback, the player pauses or stops.

No sound is audible.

Sound is distorted, noise is output.

With certain discs, loud noise is produced or play

stops.

When the auto cue function is set ON, track search

is not finished.

Back cue function cannot be carried out even

though the CUE button is pressed in playback

mode.

Pressing the LOOP OUT button does not start loop

play.

The Jog dial does not operate.

The Jog dial does not operate as desired.

DJ functions do not work.

The picture of the TV screen is fluctuated or FM

broadcast is interfered with noise.

The disc is not rotating when power is ON.

¶ Static electricity and other external effects may cause this unit to malfunction. In this case, set the POWER switch to OFF, then switch it on again after the disc has come to

a complete stop.

¶ This unit cannot playback unfinalized (partial discs) CD-R or CD-RW discs.

¶ This component is designed to play 12cm discs and 8cm discs with a commercially available adaptor, eccentrically shaped discs cannot be played since damage or malfunc-

tion may result.

¶ When using an 8cm disc with an adaptor, compared to a 12cm disc, the speed may be slower in the scratch and reverse modes etc. This component rotates at a very high speed

to generate high performance, however, in the interest of safety, the speed is lowered when an 8cm disc and adaptor are used. This is NOT a malfunction.

¶ The BPM value measured by the CDJ-1000MK2 may differ from the BPM value recorded on a CD or from our DJ mixer, but this difference is a result of differences in the BPM

value measurement method; not a result of a fault with the player.

¶ When using CD-R/RW discs, performance may be degraded depending on the quality of the recording.

About Data Recorded on MultiMedia Cards (MMC)

Users are responsible for preserving the data on their MultiMedia Cards; it is recommended that users make periodic backups of all important

data stored on their cards.

It is not the responsibility of PIONEER if the component or MMC malfunctions due to outside interference of static electricity etc. and if data on

the MMC is damaged or lost or incidental damage occurs no indemnification will be made.

Cause

÷ Power plug is disconnected from outlet.

÷ The EJECT UNLOCK/LOCK button is set to the [LOCK]

position.

÷ The auto cue function is set to on.

÷ Disc is loaded upside down.

÷ Smudges on the disc, etc.

÷ Output cables are connected incorrectly or are loose.

÷ Incorrect operation of audio mixer.

÷ Pin plugs and/or amplifier terminals are dirty.

÷ Player is in pause mode.

÷ Incorrect connections.

÷ Pin plugs and/or amplifier terminals are dirty.

÷ Interference is being picked up from a TV set.

÷ Disc has a bad scratch or warp.

÷ Disc is extremely dirty.

÷ If the sound muted portion between selections is long, search-

ing time will be long.

÷ If the sound muted portion is recorded for about 10 seconds

or more, playback will start without the auto cue function.

÷ The Cue point is not set yet.

÷ The DIGITAL OUT mode switch is set to the [NORMAL] position.

÷ No Cue points (start points) have been set.

÷ The DIGITAL OUT mode switch is set to the [NORMAL] position.

÷ Incorrect JOG MODE [VINYL/CDJ] is set.

÷ The DIGITAL OUT mode switch is set to the [NORMAL] position.

÷ Interference is being picked up from the CD player.

÷ The disc rotation stops automatically if no operation has been

performed for 80 minutes or more in pause mode

÷ When the last track on the disc is over the disc stops rotating.

Remedy

÷ Connect plug to wall outlet.

÷ Go to pause mode or cue standby mode before pressing the EJECT

button (0).

÷ Set the EJECT UNLOCK/LOCK button to the [UNLOCK] posi-

tion before pressing the EJECT button (0).

÷ Hold down the TIME MODE/AUTO CUE button for 1 second

or longer to turn off the A. CUE function.

÷ Load the disc correctly with the label side UP.

÷ Clean the smudges from the disc and then play it again.

÷ Recheck connections. Refer to installation instructions.

÷ Check the settings of the audio mixer switches and sound volume

controls.

÷ Clean away dirt.

÷ Press the PLAY/PAUSE button (6).

÷ Connect to audio mixer's LINE INPUT terminals. (Do not con-

nect to MIC terminals.)

÷ Clean away dirt.

÷ Switch OFF TV set, move player away from TV set or plug the player

into a separate outlet.

÷ Replace disc.

÷ Clean disc.

÷ Press TIME MODE/AUTO CUE button for more than 1 second

to set the auto cue function OFF.

÷ Set the Cue point. (See page 12.)

÷ The DIGITAL OUT mode switch is set to the [DJ] position.

÷ Set a Cue point.

÷ The DIGITAL OUT mode switch is set to the [DJ] position.

÷ Press the JOG MODE SELECT button to set the desired JOG

MODE [VINYL or CDJ].

÷ The DIGITAL OUT mode switch is set to the [DJ] position.

÷ Turn off POWER switch of the player, or move the player away

from the TV or tuner.

÷ Playback can be started by pressing the PLAY/PAUSE button

(6). Press the EJECT button (0) to eject the disc.