Pioneer CDJ-700S Operating Instructions Manual - Page 15

Browse online or download pdf Operating Instructions Manual for CD Player Pioneer CDJ-700S. Pioneer CDJ-700S 16 pages.

Pioneer CDJ-700S Operating Instructions Manual

TROUBLESHOOTING

Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart

below. Sometimes incorrect operation may be due to a malfunction in another component. If the problem is not fixed,

check the other components used with the player. If the problem still persists, contact your nearest Pioneer authorized

service center or dealer for service.

Symptom

Door does not open when

OPEN button is pressed.

Playback immediately stops

when started. During playback,

the player pauses or stops.

No sound is audible.

Sound is distorted, noise is out-

put.

With certain discs, loud noise

is produced or play stops.

When the auto cue function is

set ON, track search is not fin-

ished.

Back cue function cannot be

carried out even though the

CUE button is pressed in play-

back mode.

Loop playback cannot be car-

ried out even though the LOOP

OUT/EXIT button is pressed.

The picture of the TV screen is

fluctuated or FM broadcast is

interfered with noise.

The disc is not rotating when

power is ON.

¶ Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal

operation, unplug the AC power cord and then plug it in again after the disc completely stops.

¶ This unit cannot playback non-finalized CD-R discs (partial discs).

Cause

÷ Power plug is disconnected from out-

let.

÷ Disc is loaded upside down.

÷ Smudges on the disc, etc.

÷ Output cables are connected incor-

rectly or are loose.

÷ Incorrect operation of audio mixer.

÷ Pin plugs and/or amplifier terminals

are dirty.

÷ Player is in pause mode.

÷ Incorrect connections.

÷ Pin plugs and/or amplifier terminals

are dirty.

÷ Interference is being picked up from

a TV set.

÷ Disc has a bad scratch or warp.

÷ Disc is extremely dirty.

÷ If the sound muted portion between

selections is long, searching time will

be long.

÷ If the sound muted portion is re-

corded for about 20 seconds or more,

playback will start without the auto

cue function.

÷ The cue point is not set yet.

÷ The cue point (loop in point) is not

set yet.

÷ Interference is being picked up from

the CD player.

÷ The disc rotation stops automatically

if no operation has been performed

for 80 minutes or more in pause

mode.

Remedy

÷ Connect plug to wall outlet.

÷ Load the disc correctly with the label

side UP.

÷ Clean the smudges from the disc and

then play it again.

÷ Recheck connections. Refer to installa-

tion instructions.

÷ Check the settings of the audio mixer

switches and sound volume controls.

÷ Clean away dirt.

÷ Press the PLAY/PAUSE button.

÷ Connect to audio mixer's LINE INPUT

terminals. (Do not connect to MIC ter-

minals.)

÷ Clean away dirt.

÷ Switch OFF TV set, move player away

from TV set or plug the player into a

separate outlet.

÷ Replace disc.

÷ Clean disc.

÷ Press TIME MODE/AUTO CUE button for

more than 1 second to set the auto cue

function OFF.

÷ Set the cue point. (See page 10.)

÷ Set the cue point. (See page 10)

÷ Turn off POWER of the player, or move

the player away from the TV or tuner.

÷ Playback can be started by pressing the

PLAY/PAUSE button. If the OPEN but-

ton is pressed, the door will open.

OTHERS