Pioneer DEH-P6600 Installation Manual

Browse online or download pdf Installation Manual for CD Player Pioneer DEH-P6600. Pioneer DEH-P6600 6 pages. 2004 mobile entertainment systems
Also for Pioneer DEH-P6600: Owner's Manual (34 pages), User Manual (24 pages)

Print Page

DEH-P6600

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<XRD7053-A/N> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When an external power amp is being used with

negative grounding. Before installing it in a recre-

this system, be sure not to connect the blue/white

ational vehicle, truck, or bus, check the battery

lead to the amp's power terminal. Likewise, do not

voltage.

connect the blue/white lead to the power terminal

• To avoid shorts in the electrical system, be sure to

of the auto-antenna. Such connection could cause

disconnect the ≠ battery cable before beginning

excessive current drain and malfunction.

installation.

• To avoid short-circuiting, cover the disconnected

• Refer to the owner's manual for details on

lead with insulating tape. Especially, insulate the

connecting the power amp and other units, then

unused speaker leads without fail. There is a possi-

bility of short-circuiting if the leads are not insulat-

make connections correctly.

ed.

• Secure the wiring with cable clamps or adhesive

• To prevent incorrect connection, the input side of

tape. To protect the wiring, wrap adhesive tape

the IP-BUS connector is blue, and the output side

around them where they lie against metal parts.

is black. Connect the connectors of the same

• Route and secure all wiring so it cannot touch any

colors correctly.

moving parts, such as the gear shift, handbrake and

• If this unit is installed in a vehicle that does not

seat rails. Do not route wiring in places that get

have an ACC (accessory) position on the ignition

hot, such as near the heater outlet. If the insulation

switch, the red lead of the unit should be connected

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

to a terminal coupled with ignition switch ON/OFF

operations. If this is not done, the vehicle battery

• Don't pass the yellow lead through a hole into the

may be drained when you are away from the vehi-

engine compartment to connect to the battery. This

cle for several hours. (Fig.1)

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

ACC position

No ACC position

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

• The black lead is ground. Please ground this lead

impedance of 4 to 8 ohms. Connecting speakers

separately from the ground of high-current prod-

with output and/or impedance values other than

ucts such as power amps.

those noted here may result in the speakers

If you ground the products together and the ground

catching fire, emitting smoke or becoming dam-

becomes detached, there is a risk of damage to the

aged.

products or fire.

• When this product's source is switched ON, a con-

• Cords for this product and those for other products

trol signal is output through the blue/white lead.

may be different colors even if they have the same

Connect to an external power amp's system remote

function. When connecting this product to another

control or the car's Auto-antenna relay control ter-

product, refer to the supplied manuals of both

minal (max. 300 mA 12 V DC). If the car features

products and connect cords that have the same

a glass antenna, connect to the antenna booster

power supply terminal.

function.

Fig. 1