Pioneer Super Tuner III D DEH-P8600MP Installation Manual - Page 2

Browse online or download pdf Installation Manual for CD Player Pioneer Super Tuner III D DEH-P8600MP. Pioneer Super Tuner III D DEH-P8600MP 4 pages. Multi-cd/dab control high power cd/mp3/wma player with rds tuner
Also for Pioneer Super Tuner III D DEH-P8600MP: Owner's Manual (34 pages), User Manual (24 pages), Installation Manual (9 pages), Operation Manual (4 pages), Installation Manual (9 pages)

Print Page

Installation

Note:

• Before finally installing the unit, connect the

• If installation angle exceeds 60° from horizontal,

wiring temporarily, making sure it is all connected

the unit might not give its optimum performance.

up properly, and the unit and the system work

(Fig. 3)

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

60°

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

• Install the unit where it does not get in the driver's

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

• The cords must not cover up the area shown in the

figure below. This is necessary to allow the ampli-

fires to radiate freely. (Fig. 4)

DIN Front/Rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Holder

After inserting the holder into the dash-

board, then select the appropriate tabs

Fig. 3

according to the thickness of the dash-

Dashboard

board material and bend them.

(Install as firmly possible using the top

182

and bottom tabs. To secure, bend the

tabs 90 degrees.)

Rubber bush

Screw

Fig. 4

Installation without the rubber bush (Fig. 6)

Dashboard

Nut (5 mm)

Drill a 5.5 – 6.0 mm

diameter hole.

Strap

Be sure to use the strap to secure the back

Screw (5 × 16 mm)

of the unit in place. The strap can be bent

by hand to the desired angle.

Screw

Nut (5 mm)

Removing the Unit (Fig. 7) (Fig. 8)

Frame

Insert the release pin into the hole in

the bottom of the frame and pull out

to remove the frame.

(When reattaching the frame, point

the side with a groove downwards

and attach it.)

Insert the supplied extraction keys into the unit, as

shown in the figure, until they click into place. Keeping

the keys pressed against the sides of the unit, pull the

unit out.

Fig. 5

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 9)

Frame

Insert the release pin into the hole in

the bottom of the frame and pull out

to remove the frame.

(When reattaching the frame, point

the side with a groove downwards

and attach it.)

Fig. 6

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 10) (Fig. 11)

Select a position where the screw holes of the bracket and

the screw holes of the head unit become aligned (are fitted),

and tighten the screws at 2 places on each side. Use either

binding screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw holes in

the bracket

Fig. 7

Fig. 8

Factory radio mounting bracket

About the fixing screws for the front panel

If you do not operate the removing and attaching the front panel function, use the supplied

fixing screw to fix the front panel to this unit.

Fixing screw

Fig. 9

Fig. 10

Screw

Dashboard or Console

Fig.11

Fig. 12