Pioneer DV-370 Operating Instructions Manual - Page 7
Browse online or download pdf Operating Instructions Manual for DVD Player Pioneer DV-370. Pioneer DV-370 28 pages.
Print Page
Connecting up
Chapter 2
Connecting up
Easy connections
The setup described here is a basic setup that allows you to play discs using just the cables supplied
with the player. In this setup, stereo audio is played through the speakers in your TV.
A / V I N
TV
IG TAL AUD O OUT
UDIO OU
P
Y
B
COA IAL
P
R
S
IDEO O
OMPON NT V DEO OUT
White
DV-2750
Red
DV-370
Yellow
Important
• This player is equipped with copy protection technology. Do not connect this player to your TV
via a VCR using audio/video or S-video cables, as the picture from this player will not appear
properly on your TV. (This player may also not be compatible with some combination TV/VCRs
for the same reason; refer to the manufacturer for more information.)
• When connecting to your TV as shown above, do not set the Component Out setting (see Video
Output settings on page 18) to Progressive.
1
Connect the VIDEO OUT and AUDIO OUT L/R jacks to a set of A/V inputs on your TV.
Use the supplied audio/video cable, connecting the red and white plugs to the audio outputs and the
yellow plug to the video output. Make sure you match up the left and right audio outputs with their
corresponding inputs for correct stereo sound.
See below if you want to use a component or S-video cable for the video connection.
• DV-470 only: You can use either of the AUDIO OUT L/R jacks for the audio connection. Each pair
of jacks output the same thing.
2
Connect the supplied AC power cable to the AC IN inlet, then plug into a power outlet.
Note
• Before unplugging the player from the power outlet, make sure you first switch it into standby
STANDBY/ON button, or the remote control, and wait of the -OFF-
using either the front panel
message to disappear from the player's display.
• For the above reasons, do not plug this player into a switched power supply found on some
amplifiers and AV receivers.
AV ONNECTOR (RGB) TV AV Rec iver
o p o w e r
o u t l e t
Connecting using a SCART AV cable
A SCART-type AV connector is provided for connection to a TV or AV receiver. The video output is
switchable between ordinary composite, S-video and RGB. See page 23 for how to set it.
The SCART AV connector also outputs analog audio, so there is no need to also connect the AUDIO
OUT L/R jacks.
SCART
TV
DI I AL AUD O OUT
AUD O OU
P
Y
B
COAX AL
P
R
S
DEO OU
COMPON NT V DEO OUT
DV 2750
DV 370
1
Use a SCART cable (not supplied) to connect the AV CONNECTOR (RGB) output to a
SCART AV input on your TV (or AV receiver).
Connecting using the S-video output
If your TV (or other equipment) has an S-video (S1)
input, you can use the S-video output on this
player instead of the standard (composite) output
for a better quality picture.
•
Use an S-video cable (not supplied) to
connect the S-VIDEO OUT to an S-video input
on your TV (or monitor or AV receiver).
Line up the small triangle above the jack with the
same mark on the plug before plugging in.
Connecting using the component video output
You can use the component video output instead of the standard video out jack to connect this player
to your TV (or other equipment). This should give you the best quality picture from the three types of
video output available.
L
AV CONNECTOR ( GB) TV/AV Re ei er
R
S VIDEO
IN
TV
D GI AL AU IO OU
A DIO OU
Y
P
B
COAX AL
L
R
P
R
DEO OU
C M ONENT V DEO OUT
DV 2750
DV 370
7
En