Ariston L63 W Care And Use Manual - Page 9

Browse online or download pdf Care And Use Manual for Dishwasher Ariston L63 W. Ariston L63 W 36 pages.

Print Page

Never without salt

Water in your home

Water hardness varies according to where you live. If the water in your home is hard you have the possibility to

add salt in order to soften your water. The softer the water the better will be your washing and drying results.

Loading the salt.

You can use special water

softeningsalt or normalrock salt.

The salt container is situated

underneaththe lower rack, fill it

up as follows:

1. Pull out the lower rack

completely, unscrew and

remove the container cap

2. Is itthe firsttime you load the

salt? Firstfillthe containerup

with water (youwon't haveto

do this again next time)

3. Putthe dishwasherfunnel on

the

hole and

pour in

approximately70 oz. of salt.

It is normal that some water

comes out of the container.

4. Screw the cap back in place

carefully.

When should

I load the

salt?

The salt container must be filled

whenthe softener indicator light

_lS_l '

Once you have loaded the salt

for the first time, it is normal that

the low salt indicator light stays

on or flashes for 5 consecutive

cycles.

Intelligent

salt.

Your dishwasher can adjust its

saltconsumption accordingto the

hardness of the water in your

home.Thisway,youcanoptimise

andcustomiseyourdishwasher's

salt consumption (not too much,

nor too little).

Toadjustsalt consumption,do as

follows:

1. Unscrew the salt container

cap

2.There is an arrowon the neck

of the container (see figure):

if necessary,turn the arrow

anti-clockwise from the "-"

setting to the "+" setting.

Select

the arrow

position

depending

the

water

hardness, referring to the table

provided.

Water

Hardness

Salt

Auto-

Clarke

°fH

rnmol/I

Selector

consum-

nomy

degrees

position

ption

(cycles\

(Oz/cycle) 70oz.)

O- 14

O- 17

0 -1,7

14 - 36

18 - 44

1,8 - 4,4

"-"

0.7

36-71

45-

4,5-

8,9

MED

1.4

>71

> 89

> 8,9

"+"

2.1

NOTE: if you don't

find

special

water

softening

salt

you can

also

use

normal rock sail

Troubleshooting

If you have a problem, read this

Your dishwasher may not work or not function properly. In many cases, these are problems which can be solved

without having to call for a technician. Before calling the Customer Care Center, always check the points below.

The

dishwasher

won't

start

• Is the water supply tapturned

on?

• Is the water supply tap

connected

to the hose

properly?

• Has the water in your home

been cut off?

• Is the pressure of the water

supplysufficient?

• Is the hose bent?

• Is thefilter on thewater supply

hose blocked?

• Is the dishwasherdoor open?

The dishes are not clean.

• Haveyou puttherightamount

detergent

into

the

dispenser?

• Is the wash cycle suitable for

the dishes you have placed

insidethe appliance?

• Are the filter and microfilter

clean?

• Can the sprayer arms turn

freely?

The dishwasher won't drain.

• Is the drain hose bent?

Limescale

deposits

or a

white

film

form

on the

dishes.

• Is the lid on the salt container

closed properly?

• Is the rinse aid dosage

correct?

Error messages.

Yourdishwasherisequippedwith

a safety system which is able to

detect any operating problems.

These anomaliesare reportedby

one or two wash cycle indicator

lights "G"will flash rapidly.

Take a note of which lights are

flashing, turn the appliance off

and callfor technicalassistance.

Tap off alarm

If you have forgotten to turn the

water tap on, your appliancewill

remind you of this by soundinga

few short beeps for a few

minutes.Turnthe tapon and your

appliancewill start up again after

a few minutes.If you were not

home when these beeps are

sounded,the appliance will be

blocked automatically the 2nd

and 3rd light from the right will

flash rapidly.Turnthe appliance

off at the ON-OFF button, turn

on the water tap and wait

approximately 20 secondsbefore

turningtheappliancebackon;the

selectedwash cycle will start up

again.

Clogged

filter alarm

Iftheapplianceisblockedandthe

2nd andthe 4thlightfromthe right

flash rapidly,this means the filter

is clogged by large particles of

food residue.Turn the appliance

off,cleanthe filterthoroughlyand

reposition

it in its seat as

illustratedon page 10.Then turn

it back on. The selected wash

cycle will start up again.

Water load solenoid valve

malfunction alarm.

If the 3rd light from the right

flashes

rapidly,

turn

the

dishwasher off and back on

again after one minute. If the

alarm persists, first turn off the

water tap to avoid any flooding

and then cut off the electricity

supply and call for technical

assistance.

You have checked

everything, but the

dishwasher still doesn't

work and the problem

persists?

Call the Ariston Customer Care

(1-888-426-0825) and remember

to mention:

• the type of malfunction

• the model mark (Mod....) and

the serial number (S/N...)

indicated on the rating plate

located on the inner door, to

one side.

8 ARISTON DISHWASHER - User Manual