Ariston INTESA TP23 User Manual, Installation & Servicing Instructions - Page 6

Browse online or download pdf User Manual, Installation & Servicing Instructions for Boiler Ariston INTESA TP23. Ariston INTESA TP23 50 pages.

Print Page
INSTALLATION AND SERVICING INSTRUCTIONS
5. GENERAL INFORMATION
5.1
General Instructions
This manual is an integral and essential part of the product. It
should be kept with the appliance so that it can be consulted by
the user and our authorised personnel.
Please carefully read the instructions and notices about the unit
contained in this manual, as they provide important information
regarding the safe installation, use and maintenance of the prod-
uct.
For operating instructions please consult the separate Previous
User Guide.
Read the instructions and recommendations in these Installation
Instructions carefully to ensure proper installation, use and main-
tenance of the appliance.
Keep this manual in a safe place.You may need it for your own ref-
erence while our Servicing Centre technicians or your installer
may need to consult it in the future.
This is a combined appliance for the production of central heating
(C.H.) and domestic hot water (D.H.W.).
This appliance must be used only for the purpose for which it is
designed.
The manufacturer declines all liability for damage caused by
improper or negligent use.
No asbestos or other hazardous materials have been used in the
fabrication of this product.
Before connecting the appliance, check that the information
shown on the data plate and the technical data section comply
with the electric, water and gas mains of the property. You will find
the data plate on the reverse of the control panel.
The gas with which this appliance operates is also shown on the
label at the bottom of the boiler.
Do not install this appliance in a damp environment or close to
equipment which spray water or other liquids.
Do not place objects on the appliance.
Do not allow children or inexperienced persons to use the appli-
ance without supervision.
If you smell gas in the room, do not turn on light switches, use
the telephone or any other object which might cause sparks.
Open doors and windows immediately to ventilate the room.
Shut the gas mains tap (at or adjacent to the gas meter) or the
valve of the gas cylinder and call your Gas Supplier immediately.
If you are going away for a long period of time, remember to shut
the mains gas tap or the gas cylinder valve.
Always disconnect the appliance either by unplugging it from the
mains or turning off the mains switch before cleaning the appli-
ance or carrying out maintenance.
In the case of faults or failure, switch off the appliance and turn
off the gas tap. Do not tamper with the appliance.
For repairs, call your local Authorised Servicing Centre and
request the use of original spare parts. For in-guarantee repairs
contact MTS (GB) Limited.
Supplied By www.heating spares.co Tel. 0161 620 6677
Check the following at least once a year:
1 -
Check the seals for the water connections; replace any
faulty seals.
2 -
Check the gas seals; replace any faulty gas seals.
3 -
Visual check of the entire unit.
4 -
Visual check of the combustion process or analysis of com-
bustion by-products (see section 3.6) and cleaning of the
burner if needed.
5 -
If called for by point. 3, dismantling and cleaning of the com-
bustion
chamber.
6 -
If called for by point. 4, dismantling and cleaning of the burn-
er jets.
7 -
Visual check of the primary heat exchanger:
- check for overheating in the blade assembly;
- clean the exhaust fan if needed.
8 -
Adjustment of the flow rate of the gas: flow rate for lighting,
partial load and full load.
9 -
Check of the heating safety systems:
- safety device for maximum temperature
(overheat thermostat);
- safety device for maximum pressure (safety valve).
10- Check of the gas safety systems:
- safety device for lack of gas or flame ionisation
(detection electrode);
- safety device for gas cock.
11- Check of the electrical connection (make sure it complies
with the instructions in the manual).
12- Check of domestic hot water production efficiency (flow rate
and temperature)
13- General check of the combustion by-products of the dis-
charge/ventilation system.
14- Check of the general performance of the unit.
N
: T
OTE
HESE CHECKS ARE NOT EXHAUSTIVE
,
MECHANICAL
ELECTRICAL AND OPERATIONAL CHECKS MAY BE
REQUIRED AS NECESSARY
6
,
FURTHER HYDRAULIC
.
,