Ariston CP 059 MD X AUS S Operating Instructions Manual - Page 5
Browse online or download pdf Operating Instructions Manual for Oven Ariston CP 059 MD X AUS S. Ariston CP 059 MD X AUS S 16 pages. Cooker and oven
Also for Ariston CP 059 MD X AUS S: Instructions For Use And Installation (13 pages)
Print Page
Connecting the supply cable to the mains electricity
supply
For models supplied without a plug, fit a standard plug,
suitable for the load indicated on the rating plate, onto the
cable and connect to a suitable socket.
To connect directly to the mains supply, a double-pole
switch with a contact separation of at least 3 mm suitable
for the load and complying with current standards and
regulations, must be fitted between the appliance and the
mains supply outlet. The yellow-green earth wire must not
be interrupted by the switch. The supply cable must be in
such a position that no part of it can reach a temperature
of 50 °C above room temperature. For installation above a
built-under oven, the hob and the oven must be connected
separately to the electricity supply both for safety reasons
and for easy removal of the oven if necessary. Do not use
adapters or shunts as they could cause heating or burning.
Before connecting to the power supply, make sure that:
• the limiter valve and the domestic system can withstand
the load from the appliance (see rating plate);
• the supply system is efficiently earthed according to
standards and laws in force;
• the socket or double-pole switch are easily accessible
when the appliance is installed.
Important: the wires in the mains lead are coloured in
accordance with the following code:
- Earth
Green & Yellow
- Neutral
Blue
- Live
Brown
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
Connect the Green & Yellow wire to terminal marked "E"
or coloured Green or Green & Yellow.
or
Connect the Brown wire to the terminal marked "L" or
coloured Red.
Connect the Blue wire to the terminal marked "N" or coloured
Black.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION
REGULATIONS RELIEVES THE MANUFACTURER OF
ALL LIABILITY.
Replacing the cable
Use a rubber cable of the type H05VV-F with a cross section
of 3 x 1.5 mm².
The yellow-green earth wire must be 2 ÷ 3 cm longer than
the other wires.
Gas connection
Connection to the gas network or to the gas cylinder may be
carried out using a flexible rubber or steel hose, in accordance
with current national legislation and after making sure that the
appliance is suited to the type of gas with which it will be supplied
(see the rating sticker on the cover: if this is not the case see
below). When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
! Make sure that the gas supply pressure is consistent
with the values indicated in the Table of burner and nozzle
specifications (see below). This will ensure the safe
operation and durability of your appliance while maintaining
efficient energy consumption.
Gas connection using a flexible rubber hose
Make sure that the hose complies with current national
legislation. The internal diameter of the hose must measure: 8
mm for a liquid gas supply;13 mm for a methane gas supply.
Once the connection has been performed, make sure that
the hose:
• Does not come into contact with any parts which reach
temperatures of over 50°C.
• Is not subject to any pulling or twisting forces and that it
is not kinked or bent.
• Does not come into contact with blades, sharp corners
or moving parts and that it is not compressed.
• Is easy to inspect along its whole length so that its
condition may be checked.
• Is shorter than 1500 mm.
• Fits firmly into place at both ends, where it will be fixed
using clamps which comply with current regulations.
! If one or more of these conditions is not fulfilled or if the
cooker must be installed according to the conditions listed
for class 2 - subclass 1 appliances (installed between two
cupboards), the flexible steel hose must be used instead
(see below).
Connecting a flexible jointless stainless steel pipe to
a threaded attachment
Make sure that the hose and gaskets comply with current
national legislation.
To begin using the hose, remove the hose holder on
the appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose length
does not exceed a maximum of 2 metres, making sure that
the hose is not compressed and does not come into contact
with moving parts.
Checking the connection for leaks
When the installation process is complete, check the hose
fittings for leaks using a soapy solution. Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas other
than the default type (this is indicated on the rating label
on the cover).
Adapting the hob
Replacing the nozzles for the hob
burners:
1. Remove the hob grids and slide
the burners off their seats.
2. Unscrew the nozzles using a 7
mm socket spanner (see figure), and
replace them with nozzles suited to
the new type of gas (see Burner and
nozzle specifications table).
AUS
5