Ariston ENTM 19020 F Operating Instructions Manual - Page 7

Browse online or download pdf Operating Instructions Manual for Refrigerator Ariston ENTM 19020 F. Ariston ENTM 19020 F 28 pages. Refrigerator/freezer combination

Print Page

Installation

! Before placing your new appliance into operation please read these

operating instructions carefully. They contain important information for

safe use, for installation and for care of the appliance.

! Please keep these operating instructions for future reference. Pass

them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and condenser

give off heat and require good ventilation to operate correctly and

save energy.

3. Leave a space of at least 10 cm between the top part of the

appliance and any furniture above it, and at least 5 cm between

the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat (direct

sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the appliance

and the wall behind it, fit the spacers supplied in the installation kit,

following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the refrigerator by

tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it vertically

and wait at least 3 hours before connecting it to the electricity mains.

Before inserting the plug into the electrical socket ensure the following:

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance,

which is indicated on the data plate located on the bottom left side

of the fridge (e.g. 150 W).

• The voltage must be in the range between the values indicated on

the data plate located on the bottom left side (e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If the

socket is incompatible with the plug, ask an authorised technician

to replace it (see Assistance). Do not use extension cords or

multiple sockets.

! Once the appliance has been installed, the power supply cable and

the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised

technicians only (see Assistance).

! The manufacturer declines any liability should these

The manufacturer declines any liability should these

safety measures not be observed.

Start-up and use

Starting the appliance

! Before starting the appliance, follow the installation instructions

(see Installation).

! Before connecting the appliance, clean the compartments and

accessories well with lukewarm water and bicarbonate.

! The appliance comes with a motor protection control system which

makes the compressor start approximately 8 minutes after being

switched on. The compressor also starts each time the power supply

is cut off whether voluntarily or involuntarily (blackout).

1. Insert the plug into the socket and ensure that the internal light

illuminates ( the FREEZER OPERATION knob must not be on the

position OFF) .

2. Turn the FREEZER OPERATION knob and REFRIGERATOR

OPERATION knob to an average value. After a few hours you will

be able to put food in the refrigerator.

Setting the temperature

The temperature inside the refrigerator compartment automatically

adjusts itself according to the position of the thermostat knob.

min = warmest

max = coldest

We recommend, however, a medium position.

The No Frost system circulates cold air continuously to collect humidity

and prevent ice and frost formation. The system maintains an optimal

humidity level in the compartment, preserving the original quality of

the food, preventing the food from sticking together and making

defrosting a thing of the past. Do not block the aeration cells by

placing food or containers in direct contact with the refrigerating back

panel. Close bottles and wrap food tightly.

FRUIT and VEGETABLE bin

The salad crispers fitted inside the fridge have been specially

designed for the purpose of keeping fruit and vegetables fresh and

crisp. Open the humidity regulator (position B) if you want to store

food in a less humid environment like vegetable, or close it (position

A) to store food in a more humid environment like fruit.

ICE DEVICE

After pouring water in the special ice cups, place them in their places

in the ice device. After about 2 hours, the ice cubes will be ready. In

order to get the ice cubes, it will be sufficient to turn the two buttons to

the right. The ice cubes will fall in to the tray below, ready to be used.

: : : : : A compartment designed to keep meat

Food Care Zone 0°C

and fish freshness.Due to the compartment's low temperature (-2/

+3) food can be stored for even up to one week. It can also be used

for "cold meals." Not suitable for fruit, vegetables and salads.