Whirlpool 2MWTW1844 Use And Care Manual - Page 31

Browse online or download pdf Use And Care Manual for Washer Whirlpool 2MWTW1844. Whirlpool 2MWTW1844 41 pages.

Print Page

Detergent and Softener dispenser cleaning.

Interior Cleaning

Exterior Cleaning

1. Use a damp and soft cloth or a sponge to clean any

spill.

2. Use all-purpose cleaner for surfaces, if needed.

IMPORTANT: In order to avoid damage to the washer

finish, do not use abrasive products.

CARE DURING VACATIONS AND LACK OF USAGE

Start your washer only when you are at home. If you are

going to move or you are not using it for a certain period

of time, follow these steps:

1.Unplug the washer or disconnect the power supply.

2.Close the water supply to the washer to avoid floods due

to increase of water pressure.

CARE DURING STORAGE AND WINTER

IMPORTANT: In order to avoid damages, install and

keep the washer in a place where it cannot get frozen.

Due to the fact that some water may remain in the

hoses, freezing can damage the washer. If you are

going to store or move your washer during a harsh

winter season, condition it for winter.

Prepare the washer for winter:

1. Close both water outlets; disconnect and drain the water

of the filling water.

2. Pour 1 liter of RV antifreeze in the container and make the

washer start in a cycle of Rinse/Spin during 30 seconds to

mix the antifreeze with the remaining water.

3. Unplug the washer or disconnect the energy supply.

1. Remove the dispenser drawer.

To do it, open it and pull lightly

upwards.

2. Remove the siphon from the

liquid fabric softener by pulling it

upwards.

3. Rinse the dispenser and the

siphon under the warm water jet,

clean it with a damp cloth to

remove the liquid fabric softener

and/or detergent residuals and

then put again the siphon of the

softener in its place.

4. Clean the box where the

dispenser sits and clean with a

damp cloth removing detergent

and/or softener residuals.

5. Put the dispenser drawing by

pushing it lightly on the box

where it sits.

Clean the basket and

the agitator or Impeller

3D®

cleaning

exterior with a clean

and damp cloth.

WASHER TRANSPORTATION

1.Close both water faucets. Disconnect and discard the

water from the inlet water hoses.

2.If the washer is going to be transferred during a harsh

winter season, follow the instructions described in "Prepare

the washer for the winter".

3.Disconnect the draining hose from the drain system and

drain the remaining water in a pot or bucket. Disconnect the

draining hose from the lower part of the washer.

4.Unplug the electric cable.

5.Take the inlet and drain hoses inside the washer tub.

6.Take the electric cable over the border and put it in the

washer tub.

7. Place the packing materials tray for the shipment of the

originals again in the interior of the washer. If you do not

have the packing tray, put clothes or heavy towels in the

opening of the tub. Close the lid and place tape on it through

the front of the washer. Keep the lid adhered with tape until

the washer is in its place.

the

HOW TO REINSTALL OR USE THE WASHER AGAIN

To reinstall the washer after the lack of use, vacations,

storing during winter or moving:

1. Consult the Installation Instructions to locate, level

or connect the washer.

2. Before using the washer again, start the operation

following the procedure recommended as follows

To use the washer again:

1. Let the water run by the pipes and hoses. Connect the

water inlet hoses again. Open both water faucets.

2. Plug the washer or reconnect the powder supply.

3. Operate the washer in the Color Clothes cycle to clean it

and remove antifreeze, if used. Use the half of the amount of

detergent recommended by the manufacturer for a medium

size load.

Risk of Electric Shock

Plug into a grounded 3 prong outlet.

Do not remove the ground terminal.

Do not use a plug adapter.

Do not use an extension cord.

Failure to follow these instructions can

result in death, fire, or electrical shock.