Whirlpool 3XWTW5905 Use & Care Manual - Page 12

Browse online or download pdf Use & Care Manual for Washer Whirlpool 3XWTW5905. Whirlpool 3XWTW5905 36 pages. Two speed automatic washers
Also for Whirlpool 3XWTW5905: Use And Care Manual (36 pages)

Print Page

Washer leaks

Check the following:

Are the fill hoses tight? Are the fill hose washers properly

seated? Is the drain hose clamp properly installed? See the

Installation Instructions.

Is the sink or drain clogged?

Sink and standpipe must be able to handle 64 l (17 gal.) of

water per minute.

Is water deflecting off the tub ring or the load?

Center the tub before starting the washer.

The wash load should be balanced and not overloaded. The

fill or spray rinses can deflect off the load.

The washer must be level. The front feet should be properly

installed and the nuts tightened. Reset the rear leveling legs (if

needed). See the Installation Instructions.

Check household plumbing for leaks.

Washer basket is crooked

Was the washer basket pulled forward during loading?

The wash load should be balanced and not overloaded. Push

the basket to the center before starting wash.

Is the load balanced, and is the washer level?

The wash load should be balanced and not overloaded.

The washer must be level. The front feet should be properly

installed and the nuts tightened. Reset the rear leveling legs (if

needed). See the Installation Instructions.

The washer basket moves while washing.

This is normal.

Agitator operation

The top of the agitator is loose, or moves in only one

direction.

This is normal.

Dispensers clogged or bleach leaking

Did you follow the manufacturer's directions when adding

detergent and fabric softener to the dispensers?

Measure detergent and fabric softener. Slowly pour into the

dispensers. Wipe up all spills.

Dilute fabric softener in the fabric softener dispenser.

Did you put powdered or color-safe bleach into the liquid

chlorine bleach dispenser?

Add powdered or liquid color-safe bleach directly to the

basket. Do not use the chlorine bleach dispenser for color-

safe bleach.

Load too wet

Did you use the right cycle for the load being washed?

Select a cycle with a higher spin speed (if available).

Did you use a cold rinse?

Cold rinses leave loads wetter than warm rinses. This is

normal.

Residue or lint on load

Did you sort properly?

Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

Did you overload the washer?

The wash load must be balanced and not overloaded. Lint can

be trapped in the load if overloaded. Wash smaller loads.

Check the following:

Was paper or tissue left in the pockets?

Did you use enough detergent? Follow manufacturer's

directions. Use enough detergent to hold the lint in the water.

Is your water colder than 15.6°C (60ºF)? Wash water colder

than 15.6°C (60ºF) may not completely dissolve the detergent.

Stains on load

Did you follow the manufacturer's directions when adding

detergent and fabric softener?

Measure detergent and fabric softener. Use enough detergent

to remove soil and hold it in suspension.

Dilute fabric softener and add to the rinse portion of a cycle

only. Do not drip fabric softener onto clothes.

Is there above average iron (rust) in water?

You may need to install an iron filter.

Did you properly sort the load?

Sort dark clothes from whites and lights.

Did you unload the washer promptly?

To avoid transfer of dye, unload the washer as soon as it

stops.

Load is wrinkled

Did you unload the washer promptly?

Unload the washer as soon as it stops.

Did you use the right cycle for the load being washed?

Use the Synthetics/Permanent Press cycle or another cycle

with low spin speeds (if available) to reduce wrinkling.

Did you overload the washer?

The wash load must be balanced and not overloaded. Loads

should move freely during washing.

Was the wash water warm enough to relax wrinkles, or are

you using warm rinses?

Use hot or warm washes if safe for the load. Use cold rinse

water.

Are the hot and cold water hoses reversed?

Check that the hot and cold water hoses are connected to the

right taps. See the Installation Instructions.