Whirlpool 4KMVWC130 Installation Instructions Manual - Page 3

Browse online or download pdf Installation Instructions Manual for Washer Whirlpool 4KMVWC130. Whirlpool 4KMVWC130 27 pages.

Print Page
Alternate parts:
(Not supplied with washer)
Your installation may require additional parts. To order, please
contact the dealer from whom you purchased your washer or an
authorized service company.
If you have:
Overhead sewer
1" (25 mm) standpipe
Drain hose too short
Lint clogged drain

LOCATION REQUIREMENTS

Select proper location for your washer to improve performance
and minimize noise and possible "washer walk". Install your
washer in a basement, laundry room, closet, or recessed area.
27
(699 mm)
42"
(1067 mm)
You will need:
■
A water heater set to 120° F (49°C).
■
A grounded electrical outlet located within 4 ft (1.2 m) of
power cord on back of washer.
■
Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer and water pressure
of 20-100 psi (138-690 kPa).
■
A level floor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
■
Floor must support washer's total weight (with water and load)
of 315 lbs (143 kgs).
IMPORTANT: Do not install, store, or operate washer where it
will be exposed to weather or in temperatures below 32°F (0°C).
Water remaining in washer after use may cause damage in low
temperatures. See "Washer Care" section in your Use and Care
Guide for winterizing information.
Proper installation is your responsibility.
You will need:
Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump and connectors (available from
local plumbing suppliers)
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Extension Drain Hose
Part Number 285863
Connector Kit Part Number 285835
Drain Protector Part Number 367031
Connector Kit Part Number 285835
/
"
1
27"
2
(686 mm)
Recessed area or closet installation
14" max.
(356 mm)
5"
(126 mm)
1"
(25 mm)
Dimensions show recommended spacing allowed, except
for closet door ventilation openings, which are the minimum
required.
This washer has been tested for installation with spacing of
0" (0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.

DRAIN SYSTEM

Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
4.5"
(114 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than
48" (1.22 m) from bottom of washer. If you must install higher
than 48" (1.22 m), you will need a sump pump system.
3"
(76 mm)
17"
(432 mm)
1"
(25 mm)
3"
(76 mm)
39"
(990 mm)
48 in.
2
(310 cm
2
)
2
24 in.
(155 cm
2
)
3