Whirlpool AWO/D 041 Programme Chart - Page 2

Browse online or download pdf Programme Chart for Washer Whirlpool AWO/D 041. Whirlpool AWO/D 041 2 pages.

Print Page

1
2

CONSUMPTION DATA

Temperature

Programme

(°C)

Cotton

95

Cotton

60

Cotton with "Eco"**

60

Cotton

40

Synthetics

60

Synthetics

40

Delicates

30

Daily load

40

Quick wash

30

Wool

40

Handwash

40

Handwash

30

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

**

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

Add detergent as indicated on the front page and as

described in the chapter "Detergent and Additives"

in your Instructions for Use.

Close the door and turn the programme selector to the

desired programme and temperature. The indication

lamp next to the "Start/Pause" button

flashes.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the

respective indication lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch

off automatically. Unsuitable combinations of

options are deselected automatically.

"Eco" button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

"Prewash" button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time

by approximately 15 min.

• Do not use liquid detergent for the main wash

when activating the Prewash option.

"Intensive rinse" button

• More water is added and rinse cycle is prolonged.

Load

Water

Energy

Approx. Programme Duration

(kg)

(l)

(kWh)

(hours : minutes)

5.0

49*

1.90

2:00

5.0

44

0.95

2:10

5.0

44

0.85

2:20

5.0

44

0.60

2:00

2.5

50*

0.70

1:30

2.5

45

0.55

1:15

1.5

50

0.50

0:45

3.0

45

0.45

1:00

3.0

40

0.40

0:30

1.0

55

0.60

0:45

1.0

45

0.60

0:40

1.0

45

0.50

0:40

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

"Rinse hold" button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programmes "Synthetics", "Daily load" and

"Delicates".

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

Note: The programme stops to "Rinse hold" at

the time the "Rinse hold" light in the programme

sequence indication is on. The indication lamp

next to the "Start/Pause" button

Terminate the "Rinse hold" option

• Press the "Start/Pause" button

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the "Drain" programme

and press the "Start/Pause" button

"Variable spin" button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed "0" is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

START DELAY

The "Start Delay"

allows to run the machine at

the consumer's convenience, for example at night

when electricity is cheaper. Do not use liquid

detergent when activating the start delay.

• Select programme, temperature and options.

• Press the "Start delay" button to select the delay

time by 1, 3, 6, 9 or 12 hours.

• Press the "Start/Pause" button

The indication next to the "Start delay" button

flashes and goes off when the programme starts.

• Once having pressed the "Start/Pause" button

, the countdown of the time delay begins.

When the programme starts, the start delay

indicator light goes off and is replaced by the

programme sequence indication.

• After the "Start/Pause" button

pressed, the number of hours preselected can be

reduced by pressing again the "Start delay" button.

To cancel the "Start delay"

..before you press the "Start/Pause" button:

• Turn the programme selector to another

position or press the "Reset" button

..after having pressed the "Start/Pause" button:

• Press the "Reset" button

seconds - the start delay indicator light goes out.

PROGRAMME START

Open the tap and press the "Start/Pause" button

. The indication lamp next to the "Start/Pause"

button

lights up. The programme sequence

flashes.

indicator shows the current programme phase, running

:

from left to right through Wash, Rinse, Spin/Drain.

; the

When the programme phase is finished, the

corresponding indication goes out.

"DOOR OPEN" INDICATION

.

Before starting and after end of a programme, the

lamp lights to show that the door can be opened. As

long as a wash programme is running, the door

remains locked and must on no account be forced

open. In case you have an urgent need to open it

during a running programme, refer to "Cancel

(Reset) a running programme before the end".

RED INDICATIONS

"Water tap closed"

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the "Troubleshooting Guide" in the

Instructions for Use.

"Clean pump"

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

.

the latter case refer to the Instructions for Use

("Removing the Filter").

"Service"

Lighting up of the "Service" indication can be caused by

a fault in an electrical component. Refer to the

"Troubleshooting Guide" in your Instructions for Use; if

the fault persists, contact our After Sales Service.

PROGRAMME END

has been

• All the lights of the programme sequence

indicator are off, and the "Door open"

indication

lights up.

1. Turn the programme selector to the "Off/O"

position.

2. Close the water tap.

.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

for at least 3

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the "Start/Pause" button

the programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the "Start/Pause" button

new programme continues at the same position

where the previous programme was interrupted.

Do not add detergent for this programme.

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

The "Reset" button

before the end.

• Press the "Reset" button

seconds. Any existing water is drained out

before the door can be opened.

Whirlpool is a registered trademark of Whirlpool USA

to pause

again. The

cancels a programme

for at least 3

5019 301 10453

1
2