Whirlpool AWO/D 050 Brochure - Page 2
Browse online or download pdf Brochure for Washer Whirlpool AWO/D 050. Whirlpool AWO/D 050 2 pages. 5kg, 1000rpm fully integrated washing machine awo/d 049
Also for Whirlpool AWO/D 050: Instructions For Use Manual (14 pages)
Print Page
CONSUMPTION DATA
Temperature
Selector
Programme
(°C)
Cotton
95
Cotton **
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
30
Quick wash
30
Wool
40
Handwash
40
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Add detergents as indicated on the front page and
as described in your Instructions for Use.
Close the door and turn the programme selector
to the desired programme and temperature.
The indication lamp next to the "Start/Pause"
button flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
"Cold wash" button
• With this option, water is heated only up to 20ºC.
• Suitable for delicate laundry items with wash
temperature recomendation of max. 30ºC on the
care label.
• Selectable only on the lowest temperature
step of each programme.
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)
6.0
59 *
1.90
6.0
49
1.02
5.0
56
0.70
2.5
50 *
0.80
2.5
46
0.50
1.5
60
0.50
3.0
41
0.40
1.0
60
0.50
1.0
45
0.50
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from changing.
• This option is particularly recommended for
the programmes "Synthetics" and "Delicates".
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• If you select "Rinse hold" do not leave items to
soak for too long.
Note: The programme stops to "Rinse hold"
at the time the "Rinse hold" light in the
programme sequence indication is on.
The indication lamp next to the "Start/Pause"
button flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the programme
will terminate automatically with the final spin
cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause"
button
.
PROGRAMME START
Open the tap and press the "Start/Pause"
button. The indication lamp next to the "Start/
Pause" button lights up. The programme
sequence indicator shows the current programme
phase, running from left to right through Wash,
2:00
Rinse, Spin/Drain. When the programme phrase is
2:20
finised, the corresponding indication goes out.
2:00
"DOOR OPEN" INDICATION
1:35
Before starting and after end of a programme, the
1:20
lamp lights to show the the door can be opened.
0:41
As long as a wash programme is running, the door
remains locked and must on no account be forced
0:30
open. In case you have an urgent need to open
0:46
it during a running programme, refer to "Cancel
(Reset) a running programme before the end".
0:41
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be
caused by a fault in an electrical component.
Refer to the "Troubleshooting Guide" in your
"Instructions for Use"; if the fault persists, contact
our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap: if the indications still lights
up, refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether
the drain hose is kinked or the filter must be
cleaned: in the latter case refer to the Instructions
for Use ("Removing the Filter").
PROGRAMME END
• All the lights of the programme sequence
indicator are off, and the "Door open" indication
lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button again.
The new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The "Reset" button cancels a programme before
the end.
• Press the "Reset" button for at least 3 seconds.
Any existing water is drained out before the
door can be opened.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 01107