Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See "Drain System."
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 3½ ft (1.1 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-690 kPa).
A level floor with a maximum slope of ¾" (1.9 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
A sturdy floor to support the washer weight (washer, water
and load) of 260 lbs (118 kg).
Do not store or operate your washer in temperatures at or below
38°F (3.33°C). Some water can remain in the washer and can
cause damage in low temperatures. See "Washer Care" for
winterizing information.
Installation Clearances
The location must be large enough to allow the washer door to
open fully.
Washer Dimensions
³⁄ ₄
38
"
(98.43 cm)
³⁄ ₈
23
"
(59.37 cm)
*Most installations require a minimum of 4" (10.16 cm) clearance
behind the washer for drain hose clearance. See "Drain
System."
Minimum installation spacing for recessed area and closet
installation
The following dimensions shown are for the minimum spacing
allowed when the washer is to be operated with, or without, the
Stack Kit. To purchase a Stack Kit, see "Assistance or Service."
Additional spacing should be considered for ease of
installation and servicing.
Location Requirements
¹⁄ ₈
*
23
"
(58.74 cm)
¼
33
"
(84.45 cm)
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
Recessed or closet installation - Washer only
14" (35.6 cm)
18"(45.7 cm)
4"
(10.16 cm)
0"
0" (0 cm)
(0 cm)
A
A. Side view - closet or confined area
B. Recessed area
C. Closet door with vents
Recessed or closet installation - Stacked with stack kit
(Accessory)
12"
(30.5 cm)
DRYER
WASHER
0" (0 cm)
0" (0 cm)
1" (2.5 cm)
A
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
Mobile Home - Additional Location Requirements
This washer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 245, HUD Part 280).
(7.6 cm)
2
48 in.
2
(310 cm
)
2
24 in.
2
(155 cm
)
(7.6 cm)
0"
(0 cm)
B
C
3" (7.6 cm)
(7.6 cm)
2
48 in.
2
(310 cm
)
2
24 in.
2
(155 cm
)
(7.6 cm)
C
B
3"
3"
3"
3"
5
Print Page