Whirlpool Electric and Gas Dryers Installation Instructions Manual - Page 8
Browse online or download pdf Installation Instructions Manual for Dryer Whirlpool Electric and Gas Dryers. Whirlpool Electric and Gas Dryers 8 pages. Commercial dryers
Also for Whirlpool Electric and Gas Dryers: Use & Care Manual (33 pages), Use And Care Manual (28 pages), Use And Care Manual (21 pages), Use & Care Manual (31 pages)
Print Page
IMPORTANT
OPERATING
INFORMATlON
All models
as received
may have some ac-
2. Remove
air from
gas supply
line
as follows
cumulated time remaining on the timer due to fac-
(after completing
the installation):
tory testing. After connecting
the electrical
sup-
ply, use the following
to check operation.
a. Turn the dryer on and allow it to run for about
five minutes
in a full heat cycle.
ALL MODELS
1. Make sure the electric
power is connected
and
proper electrical
contact
made. Check fuses to be
sure they are good and tight.
2. To start drver:
NOTE:
Loading
door
must
be closed
for dryer
to operate.
b. If the burner does not ignite during
these five
minutes
of operation,
shut off machine
and wait
for 15 minutes,
While waiting,
check to be sure
all supply
valves are open and electric
supply
is
connected.
Repeat the above procedure
until the
burner
ignites.
MOVING OPERATIONS PROCEDURE
a. Non
coin
operated
models:
Push timer
set
button
down.
(Operating
time
will
accumulate
per number
of depressions
and type of timing cam
used.) Push START/RESTART
button.
Dryer will
stop when ti,me is used up.
b. Coin operated
models:
Insert coins in slide and
push in slowly.
Operating
time will accumulate
per
number
of coins and type
of timing
cam used.
Depress Push-to-Start
button.
Dryer will stop when
time is used up.
c. When door
is opened
dryer
stops, but timer
continues
to run. To restart, close door and push
START/RESTART
button.
3. If drying
time is too long, make sure !int screen
is clean.
GAS DRYER MODELS
1. Remove power cord from wall socket, coil it and
tape it to back of dryer.
2. Close
shut-off
valves
in gas supply
line and
behind
dryer toe plate.
3. Disconnect
gas pipe and remove
protruding
fittings
from dryer.
4. Cap the open fuel line running
to gas meter.
ELECTRIC
DRYER MODELS
1. Shut off electric
supply to the dryer.
2. Disconnect
power
supply
cord or cable
from
the.dryer
terminal
block.
4. Periodically
inspect
motor
and blower
for lint
accumulation.
Large
quantities
of lint
in these
areas will affect performance
of the dryer.
GAS DRYER MODELS
1. Make sure gas shut-off
valve IS open and gas is
available.
ALL DRYER MODELS
1. Make sure leveling
legs are secure in dryer base.
2. Apply filament
tape from Inside drum,
out the
door opening
to the front panel to prevent
drum
movement.
3. Use masking
tape to secure
clothes
door and
lint screen lid.
ILLUSTRATIONS
SHOWING COMPLETE TYPICAL INSTALLATIONS
GROUND
CONN
ELECTRIC DRY
GROUND
WIRE
(ALTERNATE)
;ROUND
CLAMP
D WATER
PIPE
ER
120 VOLTS
3 CONDUCTOR
RECEPTACLE
(15 AMP)
EXHAUST
DUCT
GAS DRYER
iiAS
SHUT-Of
F VALVES
TYPICAL ELECTRIC INSTALLATION
-
WhidpOd
CORPORATION
TYPICAL GAS INSTALLATION
Part No. 687455
Benton
Harbor,
Michigan
49022
8