Whirlpool WGD70HEBW Use And Care Manual - Page 12

Browse online or download pdf Use And Care Manual for Dryer Whirlpool WGD70HEBW. Whirlpool WGD70HEBW 40 pages. Whirlpool duet 7.4 cu. ft. front load electric dryer with eco monitor
Also for Whirlpool WGD70HEBW: Instruction Manual (8 pages), Installation Manual (44 pages), Installation Instructions Manual (44 pages)

Print Page

CYCLE STATUS INDICATORS

Appearance may vary.

The Cycle Status Indicators show the progress of a cycle.

–/+ (Adjust drying time indicators)

The –/+ indicators will light when a Manual Cycle has been

selected.

Check Vent

This indicator will show the status of airflow through the

dryer for the dryer's life. During the sensing phase at the

beginning of the cycle, the Check Vent light will come on if a

blocked vent or low airflow issue is detected. This light will

stay on for the entire cycle, but will turn off at the end of the

cycle. This feature is available during Automatic and Steam

cycles only. For more information on maintaining good

airflow, see "Check Your Vent System for Good Airflow."

NOTE: If there are other error issues during a cycle, the

Check Vent indicator will not light up. See "Troubleshooting"

section.

Eco Monitor (on some models)

The Eco Monitor allows you to see how the settings you

select affect your energy usage within the cycle chosen.

The Eco Monitor indicator may change, depending on the

options and modifiers selected.

Wet

The load is still wet and/or the cycle just started.

Damp (on some models)

This indicator shows that the load is partially dried and items

that you may wish to hang up or iron while still damp may

be removed.

Cool Down

The dryer has finished drying with heat, and is now tumbling

the load without heat to cool it down and reduce wrinkling.

Done

This will indicate that the selected cycle has ended and

the load may be removed from the dryer. If Wrinkle Shield

option has been selected, the dryer may continue to tumble

the load, even if the Done indicator is lit.

Sensing (on some models)

The Sensing indicator will light to indicate that the moisture

sensor on the dryer is operating.

Steaming (on some models)

This indicator will light when the Steam function is active.

NOTE: Steam is not available on all models or on all cycles.

Wrinkle Shield

Option (on some models)

™

This indicator will light if the Wrinkle Shield

selected and is running. The dryer will periodically tumble

the load for up to 140 minutes after the cycle has ended.

ADDITIONAL FEATURES

To obtain a drying rack for your dryer, order by calling

1-877-944-7566. You will need your model and serial

number and the purchase date. Remove and discard

any packing material before use.

Use the Drying Rack for items that you do not want to

tumble dry, such as sweaters and tennis shoes. When you

use the drying rack, the drum continues to turn, but the rack

remains stationary.

The drying rack is intended for use with the Manual Dry/

Timed Dry cycles only. The drying rack cannot be used

with Automatic cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

2. Align the two hooks on the front of the drying rack with

™

3. Place wet items on top of the drying rack. Allow space

4. Close the door.

5. Select a Timed Dry/Air Only, or Low Temperature cycle.

6. When the cycle is selected, the Estimated Time

option has been

™

7. Start the dryer.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack

after the cycle is finished.

USING THE DRYING RACK

the holes in the dryer door opening and press down fully

into holes. Rest the rear support on the dryer back ledge.

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside of

the dryer drum. Make sure items do not hang over the

edges or between drying rack grille.

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only setting.

Remaining display shows the default time. You can

change the actual time in the cycle by increasing or

decreasing the cycle time.