-.
Cabinet
opening dimensions
that ore
shown must be used Gwen drnensons
Before you start.. .
FOR YOUR SAFETY
To avoid possible
exposure
to
excessive
microwave
energy:
1. Do not atlempt to operate this
oven with the door open. Open-
door operation
can result in
harmful microwave
energy
exposure.
2. Do not tamper with or defeat the
safety interlocks.
3. Do not place objects
between
the oven front face and the door.
4. Do not allow soil or cleaner
residue to accumulate
on
sealing surface of door.
5. Do not operate oven if damaged.
The door MUST
close pro erly
to provide
safe operation.
g o
not use the microwave
if:
l
door is bent
l
hinges and latches are broken
or loose
- door seals, sealing surfaces
or
glass is broken.
The oven should only be
adjusted
and repaired by a
qualified
repair person.
6. Have a qualified
repair person
check oven for microwave
leakage after a repair is made.
Proper insiallol~on IS your responslbil@
provrde 0' clearonce
Drmensrons
Make sure you have everythIng
grven are for built r oven setting on
necessary for correcl ~nstallal~on II IS
coniocl surface 2 %' below the open
the rejponslblllty of the ~nsioller to
lower door helghl Co&cl
surface
comply with the ~nstallatlon clearance
must be solld and level
specl'led on the serial roling plate
The strlollrai~ng plate can be found
behir3 the microwave door on the
I I
The recessed installation
area must
orovrde comolete
enclosure around
I
frame of the m~crowwe oven
, II
I I
ihe recessed portion of the oven
I
Remove all packagrng
material from
microwave
oven cavity Check the
oven area for damage
See For Your
Safety II any damage
is evident. do not
operate mrcrowave oven untrl it IS
checked by an authorized Whrrlpco
service technician
----- --
I
I
I
I
I
I__---
\
\
\
\
\ ,
b
1
FORYOUR SAFETY
1
To avoid potential
personal
Injury,
this oven must be fastened
to the
/
cabmet usmg four screws that are
provided.
Important:
Observe
all
governing
codes
and
ordinances.
WARNING:
The microwave
oven in this unit is
designed
for household
use only.
Do not use microwave
for
commercial
purposes.
WARNING:
It is the customer's
responsibility:
l
To contact a qualified
electrical
installer.
l
To assure that electrical
installation
is adequate
and in
conformance
wlth National
Electrical
Code, ANSVNFPA
70-1987'
and local codes and
ordinances.
b
AC-\
boym
of the cabinet cutout
Note, Clearances
specrfied are for
combustible walls and materials that
have a densrty of 20 or more pounds
per cubic foot. No evaluation of
clearances has been made for
installatrons adjacent to materrals that
are less than 20 pounds per cu. ft or
to plosttc tiles and sheetrng
Check locatron where the built-In oven
wrll be installed. The locotron should be
away from strong draft areas. such
as windows. doors and strong heatrng
vents or fans. The built-in oven should
be located for convenient use rn
krtchen
Tools needed
for installation.
frequency as specrfred on the serial/
rating plate. A separate 40 ampere
Circuit is required. Fuse both sides of the
line. DO NOT fuse the neutral. A time-
delaY fuse or circuit breaker IS
recommend&.
E.
Locate the junction box to allow
as much slack in the cable as possible
between the Junction box and the
appliance
so that the oven can be
moved if servicing is ever needed
OVEN MUST BE CONNECTED WITH
COPPER WIRE ONLY Aluminum wire
mUSt not be used to avoid potentiblly
unsatisfactory connections.
A U.L. recognized
strain relief must be
provided at the junction box.
Electrical
requirements
Electrical
ground
is required
on
this appliance.
C
Wire sizes must conform
n to the requirements
of the National Electrical
Code. ANSVNFPA 70.1987' and local
codes and ordinances for the kilowati
rating of the oven. This rating can be
found on the serial/rating plate behind
;tm;icrowave
oven door on the front
G.
It is the personal responsibility and
obligation of the customer to contact a
qualified electrician to assure that the
electrical installation is adequate
and is
in conformance
with the National
Electrical Code ANSVNFPA 704987' and
local codes and ordinances.
Copies of the standards listed may be
obtained from:
*Nattonal
Fire Protecflon
Association
Batterymarch
Park
Qulncy, Masxrchuseffs
02269
H
A wlnng dragram is
n
included in the
tech sheet. The tech sheet is located
behrnd the control wnel.
Save
installation
instructions
for
the local
electrical
inspector's
use.
A
I
Thus appliance
must
be connected
to the proper electrical voltage and
Panel A
D.
This appliance
should be connected
to the fused disconnect (or circuit
breaker) box throuah flexible armored or
non-meiallic
sheathed copper cable
(wrth grounding wire]. The flexible
ormored cable extending from the
appliance
should be connected
directly
to the ynctron box
Print Page