Whirlpool UXG7360VDS0 Use & Care Manual - Page 9
Browse online or download pdf Use & Care Manual for Ventilation Hood Whirlpool UXG7360VDS0. Whirlpool UXG7360VDS0 28 pages. 30" (76.2cm), 36" (91.4cm) and 48" (121.9cm) wall-mount canopy grill vent hood installation instructions
Print Page
GRILLVENTHOOD USE
The grill vent hood is designed to remove smoke, cooking vapors
and odors from the grill area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the area.
Control Panel
The grill vent hood controls are located on the right-hand front
surface of the grill vent hood.
_D
A
B
A. Fan on/off and low/high fan speed
B. Lights on/off
Operating the Light
1. Press the light ON/OFF button (B) to turn on the light.
2. Press the light ON/OFF button (B) to turn off the light.
Operating
the Fan and Adjusting
Fan Speed
The fan has 2 speeds, Low and High.
1. Press fan button (A) "up" to turn fan on Low Speed. Press the
fan button "down" to turn fan to High Speed.
2. Press fan button (A) to the middle position to turn off the fan.
Thermal
Overload
The grill vent hood is equipped with a thermal overload to avoid
overheating conditions.
If the grill vent hood shuts off while in
use, press the on/off button to turn off the grill vent hood. Wait
approximately
60 minutes, then press the on/off button to restart
the grill vent hood.
GRILLVENTHOOD CARE
IMPORTANT: Clean the hood, grease filters and grease trays
frequently according to the following instructions.
Replace grease
filters before operating hood.
Be sure lights are cool before cleaning the hood.
STAINLESS
STEEL
IMPORTANT: Do not use soap-filled
scouring pads, abrasive
cleaners, Cooktop Polishing Creme, steel wool, gritty wash
cloths or paper towels.
To avoid damage to the stainless steel, do not use cleaners that
contain chlorine.
Food soils should be cleaned as soon as entire grill is cool. Soils
may cause permanent discoloration.
Cleaning
Method:
•
Rub in direction of grain to avoid scratching
or damaging the
surface.
•
Stainless Steel Cleaner and Polish Part Number 31462 (not
included):
See "Assistance
or Service" section to order.
•
Liquid detergent or all-purpose
cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
•
Glass cleaner to remove fingerprints.
EXTERIOR
The quality of this material resists most stains and pitting,
providing that the surface is kept clean and protected.
•
Apply stainless steel polish to all areas before first use.
Reapply after each cleaning to avoid permanent damage to
surface.
Cleaning should always be followed by rinsing with clean
warm water.
Wipe the surface completely
dry with a soft cloth.
For tough spots or baked-on grease, use Heavy Duty
Degreaser Part Number 31552 (not included), a commercial
degreaser designed for stainless steel.
See "Assistance
or Service" section to order.
INTERIOR
Discoloration
of stainless steel on these parts is to be expected,
due to heat from the grill. Always rub in the direction of the grain.
Cleaning should always be followed by rinsing with clean, warm
water.
Cleaning
Method:
•
Liquid detergent or all-purpose
cleaner.
•
Rinse with clean water and dry completely with a soft, lint-
free cloth.
•
A heavy-duty scrub sponge can be used with mild cleaning
products.
For small, difficult-to-clean
areas, use Heavy Duty Degreaser Part
Number 31552 (not included), a commercial degreaser designed
for stainless steel.
See "Assistance
or Service" section to order.
METAL GREASE FILTERS
The grease filters should be washed frequently. Place grease
filters in dishwasher or hot detergent solution to clean.
Drain water and let each filter dry thoroughly
before replacing it.