Whirlpool UXG7480VDS0 Use & Care Manual - Page 4
Browse online or download pdf Use & Care Manual for Ventilation Hood Whirlpool UXG7480VDS0. Whirlpool UXG7480VDS0 28 pages. 30" (76.2cm), 36" (91.4cm) and 48" (121.9cm) wall-mount canopy grill vent hood installation instructions
Print Page
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill with 1W' (3.0 cm) drill bit
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
•
Scissors
Parts needed
•
Home power supply cable
•
1 - 1/2"(12.7 ram) UL listed or CSA approved strain relief
•
1 wall or roof cap
•
Metal vent system
•
Vent clamps
•
6 to 8 #10 or larger screws to mount grill vent hood and wood
mounting strip (quantity and type determined
by size of grill
vent hood and wall type). If larger screws are used, the holes
in the grill vent hood may need to be enlarged.
•
1" x 4" (2.5 cmx 10.2 cm) wood mounting strip (length
determined by grill vent hood width)
Parts supplied
Remove parts from packages. Check that all parts are included.
•
2 metal grease filters for 30" (76.2 cm) models
3 metal grease filters for 36" (91.4 cm) models
4 metal grease filters for 48" (121.9 cm) models
•
Metal transition duct piece
•
8 - #10 Phillips transition duct screws
•
UL listed wire connectors
(3)
•
Light bulb removal tool
IMPORTANT." Observe all governing codes and ordinances.
Have a qualified technician install the grill vent hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located inside the grill vent hood on the rear wall of the
grill vent hood.
Canopy grill vent hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy grill vent hood is factory set for venting through the
roof or wall.
All openings in ceiling and wall where canopy grill vent hood will
be installed must be sealed.
Product Dimensions
Vented Installations
4"
(10.2 cm)
12"
(30.5 cm)
30" (76.2 crn)
36" (91.4 crn).
48" (121.9¢m)_
(61.0 cm)
t
18"
(45.7 cm)
Installation Dimensions
\
A
.... X
A. Distance "X" (30" [76.2 cm] min, suggested
36"
[91.4
cm] max)
*NOTE: The grill vent hood duct cover is designed to add
12" (30.5 cm) to meet the ceiling or soffit height. Depending on
your model, order:
Part Number W10153151 for 30" (76.2 cm) models,
Part Number W10153152 for 36" (91.4 cm) models, and
Part Number W10153153 for 48" (121.9 cm).
IM PO RTANT:
Minimum distance "X": 30" (76.2 cm)
Suggested maximum distance "X": 36" (91.4 cm)