Whirlpool UXT4236ADW0 Installation Instructions And Use & Care Manual - Page 5
Browse online or download pdf Installation Instructions And Use & Care Manual for Ventilation Hood Whirlpool UXT4236ADW0. Whirlpool UXT4236ADW0 28 pages. 30" (76.2 cm) and 36" (91.4 cm) range hood
Print Page
For the most efficient and quiet operation:
•
Use no more than three 90 ° elbows.
•
Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
•
Do not install 2 elbows together.
•
Use clamps or duct tape to seal all joints in the vent system.
•
The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.
•
Use caulking to seal exterior wall or roof opening around the
cap.
Calculating
Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
Vent System
Vent Piece
45 ° elbow
2.5 ft
(0.8 m)
Example vent system
90 ° elbow
-r-
2 it (0.6 m)
_!=
1 - 90 ° elbow
1 - wall cap
8 ft (2.4 m) straight
System length
= 5.0 ft (1.5 m)
= 0.0 ft (0.0 m)
= 8.0 ft (2.4 m)
= 13.0 ft (3.9 m)
Maximum Recommended
Length
7" (17.8 cm) Round Vent
= 50 ft (15.2 m)
31/4 '' x 10" (8.3 x 25.4 cm)
Rectangular Vent
= 35 ft (10.7 m)
90 ° elbow
5.0 ft
(1.5 m)
31/4 '' x 10" (8.3 cm x
12.0 ft
25.4 cm) flat elbow
(3.7 m)
7" (17.8 cm) wall cap
0.0 ft
(0.0 m)
31/4 '' x 10" (8.3 cm x
4.5 ft
25.4 cm) to 7" (17.8 cm)
(1.4 m)
31/4 '' x 10" (8.3 cm x
5.0 ft
25.4 cm) to 7" (17.8 cm)
(1.5 m)
90 ° elbow
E ectrica
Requirements
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance
with National Electrical Code, ANSl/NFPA 70 (latest
edition), or CSA Standards C22.1-94, Canadian Electrical Code,
Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it is
recommended
that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch
Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
•
A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is
required.
•
If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors
and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must conform with
local codes and industry accepted wiring practices.
Wire sizes and connections
must conform with the rating of
the appliance as specified on the model/serial
rating plate.
The model/serial plate is located behind the filter on the rear
wall of the range hood.
Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22.1-94,
Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.