Whirlpool W10320580C User Manual - Page 4

Browse online or download pdf User Manual for Ventilation Hood Whirlpool W10320580C. Whirlpool W10320580C 28 pages. 30" (76.2 cm) and 36" (91.4 cm) wall-mount canopy range hood

Print Page

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■

Level

Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), and ⁵⁄₁₆" (7.9 mm) drill bits

■

Pencil

■

Wire stripper or utility knife

■

Tape measure or ruler

■

Pliers

■

Caulking gun and weatherproof caulking compound

■

Vent clamps

■

Jigsaw or keyhole saw

■

Flat-blade screwdriver

■

Metal snips

■

Phillips screwdriver

■

Metric hex key set

Parts needed

■

Home power supply cable

■

½" (12.7 mm) UL listed or CSA approved strain relief

■

3 UL listed wire connectors

For vented installations, you will also need:

■

1 wall or roof cap

■

Metal vent system

For non-vented (recirculating) installations, you will also need:

■

Recirculation Kit Part Number W10349327 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

■

6" (15.2 cm) dia. round metal vent duct - length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

■

Hood canopy assembly with ventilator and light bulbs

installed

■

Vent transition with back draft dampers installed

■

Metal grease filter(s)

■

Vent cover support bracket

■

Mounting template

■

2-piece vent cover

■

2 - 3.5 x 9.5 mm screws

■

2 - 2.9 x 6.5 mm screws

■

6 - 5 x 45 mm mounting screws

■

2 - 8 x 40 mm wall anchors

■

4 - 10 x 60 mm wall anchors

■

4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

■

T20

®†

Torx

adapter

®†TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC..

INSTALLATION REQUIREMENTS

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "For Non-

vented (recirculating) Installations Only" in "Connect Vent

System" section. Recirculation Kit Part Number W10349327

is available from your dealer or an authorized parts distributor.

NOTE: This product will not comply with Energy Star

specifications when installed as non-vented (recirculating)

with the optional recirculation kit.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

7¹⁄₄"

(18.3 cm)

30" (76.2 cm) or

36" (91.4 cm)

*For non-vented (recirculating) installations

**For vented installations

8¹⁄₈"

(20.7 cm)

*28⁷⁄₈" (72.6 cm) min.

42¹⁄₁₆" (106.9 cm) max.

**28³⁄₈" (72.0 cm) min.

38" (96.6 cm) max.

14¹⁄₈"

(35.9 cm)

10"

(25.4 cm)

20" (50.8 cm)

1¹ ₂" (4.0 cm)